![]() |
|
![]() |
#1 |
Senior Member
![]() Join Date: Mar 2012
Location: Chesapeake, Va
Posts: 1,275
|
track arm question
I did a rebuild on the rear section of my truck. Bushings, springs/ trailing arms etc. etc....
I went to put the rear track arm with new bushings . And is it normal for the holes not to line right up and the arm pop right in?? right now i am about 1/2 to 3/4 inches off and have to push to the right (passenger side) to get the eyes to line up for the bolt, Is this normal to be that far off?
__________________
Mike 72 C-10 Cheyenne off frame resto and Upgraded to 4 wheel disk, Tilt, Dakota Digital Dash / Rear slider. 421 SBC / TH350 3000RPM Stall Progression Ignition /Holley 750 DP/3:73 gear Eaton Limited Slip unit / 2 1/2 exhaust glasspacks ![]() |
![]() |
![]() |
![]() |
#2 |
Post Whore
![]() Join Date: Feb 2016
Location: Portland Oregon
Posts: 11,136
|
Re: track arm question
Yes it is. I used a Come-A-Along and a hydraulic jack to bring mine into alignment. Is yours adjustable?
Here is a link to what I did to center my Burban's rear end before installing my new adjustable track bar. Scroll down to post 513. https://67-72chevytrucks.com/vboard/...698377&page=21
__________________
Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. ![]() RIP Bob Parks. 1967 Burban (the WMB),1988 S10 Blazer (the Stink10 II),1969 GTO (the Goat), 1970 Javelin, 1952 F2 Ford OHC six 4X4, 29 Model A, 72 Firebird (the DBP Bird). 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377 |
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: Mar 2012
Location: Chesapeake, Va
Posts: 1,275
|
Re: track arm question
mine is not adjustable but i will pull it over
thanks Mike
__________________
Mike 72 C-10 Cheyenne off frame resto and Upgraded to 4 wheel disk, Tilt, Dakota Digital Dash / Rear slider. 421 SBC / TH350 3000RPM Stall Progression Ignition /Holley 750 DP/3:73 gear Eaton Limited Slip unit / 2 1/2 exhaust glasspacks ![]() |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jan 2019
Location: Hampton Roads VA
Posts: 644
|
Re: track arm question
Hah funny I am ready to do the same. Maybe you can ride up to Yorktown to show me how its done
![]() Thanks HO455
__________________
70 C20 Build link : Project Montezuma http://67-72chevytrucks.com/vboard/s...d.php?t=794479 How to repair that rusted out 67-72 c10-c30! Please subscribe! https://www.youtube.com/c/MaycoCustomRestorations |
![]() |
![]() |
![]() |
#5 | |
Senior Member
![]() Join Date: Mar 2012
Location: Chesapeake, Va
Posts: 1,275
|
Re: track arm question
Quote:
I will just use a chainfall and maybe strap it to anchor point in the garage or another vehicle bumber and slowly bring it over to line up the holes
__________________
Mike 72 C-10 Cheyenne off frame resto and Upgraded to 4 wheel disk, Tilt, Dakota Digital Dash / Rear slider. 421 SBC / TH350 3000RPM Stall Progression Ignition /Holley 750 DP/3:73 gear Eaton Limited Slip unit / 2 1/2 exhaust glasspacks ![]() |
|
![]() |
![]() |
![]() |
Bookmarks |
|
|