Oil Bath Breather

[AJLChase]

Was curious as to where I could find information on how to change my oil on my 67. It's got a 327 with the Oil bath still on it. I've looked online with only the ability to find out how to change regular oil filters and air filters. Thanks!

[dwcsr]

oil bath filters are either 2 piece or 3 piece. Take the center wingnut off and seperate the halfs remove the lower have from the carb dump the oil and refil to the line then assemble the halfs . I'm supprised to see a oil bath on that late of a truck. post a picture of it.

[vectorit]

My 68 came with an oil bath air cleaner.
Back when I ran the oil bath on the burb, I would dump out the old dirty oil then clean out the housing with a solvent. Pay special attention to the base of your bath, since that is where most of the dirt will settle. There was an element that would stay soaked with oil, this is basically your dust and dirt catcher so this has to be cleaned as well. I would back in the day just soak it in a pan of gasoline, but I'm sure there is a safer and better way of doing this now. None the less you want that screen to be as clean as possible. Once you have it all clean, just refill it with a 30wt or something similar to the fill line. I would also soak the screen seperately to make sure it was completley covered in oil.

The connector that breaths from the valve cover to the stack, I just would shoot carb cleaner though it and try to shake out any gunk left in it.

I may be totally off on this, since the last time I did this was - uh 20+ years ago.

[72lb4x4]

As dwcsr said, but you probably want to clean all the bits as well.

You might measure the carb diameter where the filter sits, and troll the scrapyards for a paper type element filter assembly. Note the info on the vehicle so you can get a replacement element. The paper filters are supposed to be much better at keeping the small rocks out of the motor. Snag the wing nut and stud too...

[AJLChase]

But for the rest of it, unscrew the plug down at the bottom and drain the oil then cap it back on then poor the oil in as usual?

[Stocker]

Originally Posted by AJLChase

But for the rest of it, unscrew the plug down at the bottom and drain the oil then cap it back on then poor the oil in as usual?

Yes, and be sure to change the engine oil filter also. Now.... is it a modern screw-on or drop-in canister type?

As vectorit said, be sure to clean out your air filter with solvent, they dry before refilling with fresh oil. And yes, oil bath air filters are supposed to be the best thing for extremely dirty environments. No clue how their flow rates compare with paper elements, but probably pretty well. They're just very messy to deal with and not worth the trouble for most of us. If it were mine, I'd replace it with a paper filter....

[69GMCLonghorn]

Does anybody know how well these things breathe as compared to an open element? Are they very restrictive? I tossed my out the door about 5 minutes after I bought the truck. For the novelty of it, I kind of wish I would have kept it.

[don t. - 72gmc]

I have no idea about oil bath filters on our trucks, but I do have an oil bath filter on my 45 ford tractor. Oil bath are supposed to be a better filter than any paper filter, related to clean air. I've been told they are no more restrictive than a paper filter.

HTH....don t. ....

[vectorit]

Personally I'd like to learn more about it myself.
My burb came with one, and was actually an option on the SPID.

I've heard they are best for extreme environments, where there is a lot of dirt and dust.

I know back in the day they were probably the best thing, and today they are obsolete obviously. But I'd really like to use mine again, since it is original to the truck. But finding the screen element has been futile for me over the years, and I am always on the look out for one and if n when I find it the oil bath is going back on.

[don t. - 72gmc]

Vectorit....On the ford tractor, its just a metal mesh. Before I knew more, I used 3 stainless steel chore-boy scrubbing pads. I kinda stretched them out abit so they would fit.

If you stay on top of cleaning the oil in the filter, you should rarely haffta clean the mesh. The oil gets sucked up into the mesh, the crap gets stuck. When you shut down, gravity of the oil "should" flush the mesh of the debris.

Caveat...like I said, I know nothing about o-b-filters on our trucks, but would think they logically work the same.

HTH.....don t. .....

[eagleuh1]

I think your supposed to use 70 or 80 weight oil per the owners manual. I'll check when I get home. I use my oil bath air cleaner on my 68 and it runs fine. Just fill up to the mark on the plastic ring that goes in the bottom.

[Longhorn Man]

the EPA is the main reason the oil bath went away. Paper is easier, but oil bath gets more dirt out. However, oil mist can, and does get in the incoming air and burns in the cylinder, causing more pollution than needed.

[Stocker]

I was thinking we used cheap (recycled bulk) engine oil when I was a kid, but that's been about 45 years ago so.....

Anyway a quick Google search came up with this:

http://vintagetractorengineer.com/20...-for-tractors/

Use the correct grade (weight) of oil. If the oil is too heavy it will not be carried up by the air onto the packing material. Conversely, if the oil is either too light or the reservoir is too full then oil can be carried through the packing material and towards the engine. In petrol fuelled models this can enrich the fuel mixture in the carburettor and not only increase exhaust emissions of unburned hydrocarbons but also increase fuel consumption. Inspect the inside of the clean pipe for any traces of oil. If you cannot find the specification for the oil then as a general rule your system will usually be designed to use the same type of oil as the lubricating oil in the engine. In very cold conditions it may be necessary to use a lighter oil or dilute the oil with up to 25% paraffin to manipulate the oil viscosity.

[eagleuh1]

For about $20 you can get the conversion mount to use a satndard spin on oil filter. Most parts stores or Summit has them. Putting mine on today. Jim