![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Foolish Mortal
Join Date: Mar 2007
Location: Livermore, CA
Posts: 243
|
"klunking" when I turn....
Can anyone clue me into the seriousness of this problem? Basically here's what happens:
I'm driving along, and I slow down to a stop, to turn right, for example. I "creep" forward without fully releasing the brake and I FEEL a sort of "klunk" when I let the brake off to creep forward... Sorry for the technical jargon, but I'm not much of a mechanic =] |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
|
Re: "klunking" when I turn....
Sounds like you have something loose on the front end, probably a tie rod. I would get under there and check it all out. All of those front end parts (tie rods, ball joints, etc) are pretty important.
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs. |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Mar 2001
Location: Paradise TX USA
Posts: 1,200
|
Re: "klunking" when I turn....
Check your upper control arms to see if the bolts are loose, or any shims have fallen out.
__________________
"Negative people always seem to have a problem for every solution" |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
|
Re: "klunking" when I turn....
Check your steering box too. I had the bolts holdind one on work loose on me once. Frames also like to crack right where one of the bolt holes for the steering box is too.
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs. |
![]() |
![]() |
![]() |
#5 |
Foolish Mortal
Join Date: Mar 2007
Location: Livermore, CA
Posts: 243
|
Re: "klunking" when I turn....
I'll check them for sure, but I should have mentioned one more issue-the klunking feels like it's coming from behind the vehicle (or maybe directly underneath me)-however, that doesn't mean the problem's actually there
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Mar 2001
Location: Paradise TX USA
Posts: 1,200
|
Re: "klunking" when I turn....
It could also be loose or missing trans crossmember bolts, or rear trans mount worn out.
__________________
"Negative people always seem to have a problem for every solution" |
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
|
Re: "klunking" when I turn....
The turning may be a coincidence. Check your U-joints too.
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs. |
![]() |
![]() |
![]() |
#8 |
Foolish Mortal
Join Date: Mar 2007
Location: Livermore, CA
Posts: 243
|
Re: "klunking" when I turn....
Ok, I'm going to take a pic of the transmission mount and post it-I'm not sure if that's the culprit, but to my (untrained) eye, it looks like it is kinda chewed up....
In the meantime, anyone got a pic of what the transmission mount's supposed to look like? |
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
|
Re: "klunking" when I turn....
I just replaced a bad one on my truck last week. You can't really tell just by looking at it. I had the crossmember out of the way, so I stuck a bolt in it and pulled, and the rubber wasn't holding anything in place. They are cheap, and fairly easy to replace. Moving the crossmember is 95% of the work.
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs. |
![]() |
![]() |
![]() |
#10 |
Recovering 67-72 Addict
![]() Join Date: Oct 2000
Location: North Bend, WA
Posts: 1,788
|
Re: "klunking" when I turn....
A bit off topic but I've not found it necessary to move the crossmember. Just unbolt the trans mount from the crossmember, jack up the trans, reach between the trans and crossmember to unbolt the mount. Then do the reverse to put the new one in.
__________________
68 Short Fleet 4x4; 427; BTO Level 3 700R4; NP205; Dana 60 front and rear; 4" lift with 35's; Disc brakes; AGR variable ratio steering; factory bucket seats; factory tach and tilt. "Friends call me cruzer cuz I like fast cars and fast women" |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Jun 2007
Location: Cary, N.C.
Posts: 1
|
![]()
My 69 shortbed is doing the exact same thing, sounds like its in the rear end.I took my bed off and it looks like the drive shaft is not centered in the drive loop.I have lowered mine a couple inches in the rear,I did not change the tracking arm to an adjustable one, so I think it pushed my rear to the passenger side enough the the drive shaft hits the drive loop. Mine make that loud sound when I stop then turn wheel to the left and pull off real slow.I Can feel it shake the truck. Hope this might help. If you find something else please let me know. Charles
|
![]() |
![]() |
![]() |
#12 |
Gone to greener pastures
![]() Join Date: May 2007
Location: Gateway to the Delta
Posts: 7,354
|
Re: "klunking" when I turn....
If it's "clunking" in a low speed turn, and you have a posi rear end, you just might need some "posi" lube.
My Chevy was doing the same thing. It almost felt like the 3rd member was trying to shift a bit, side to side. I pulled the rear cover, just to take a look at things, and repair the weeping gasket; put in a bottle of "posi" lube topped it off with a synthetic gear lube (I forget what flavor). And the "clunk went away. All in all, a pretty cheap fix.
__________________
'69 Chevy 1/2 T LWB Stepper: Daily Beater '72 GMC 3/4 T Fleet: Another Daily Beater '72 Plymouth Gran Coupe: ? "Ah women. They make the highs higher and the lows more frequent." Friedrich Nietzsche "Never kick a fresh turd on a hot day." Harry S. Truman GUN CONTROL: Never having to say, "I missed you." Always fire two warning shots into your attacker's chest area before putting a bullet between his eyes. Paraphrased from Louis Awerbuck |
![]() |
![]() |
![]() |
#13 |
2WD Jimmy
![]() Join Date: Mar 2005
Location: Davis County, Utah
Posts: 2,564
|
Re: "klunking" when I turn....
If you have an original posi rearend, its exactly what EL JAY said. Get some Posi conditioner from Napa and youll be good to go.
|
![]() |
![]() |
![]() |
#14 | |
Gone to greener pastures
![]() Join Date: May 2007
Location: Gateway to the Delta
Posts: 7,354
|
Re: "klunking" when I turn....
Quote:
__________________
'69 Chevy 1/2 T LWB Stepper: Daily Beater '72 GMC 3/4 T Fleet: Another Daily Beater '72 Plymouth Gran Coupe: ? "Ah women. They make the highs higher and the lows more frequent." Friedrich Nietzsche "Never kick a fresh turd on a hot day." Harry S. Truman GUN CONTROL: Never having to say, "I missed you." Always fire two warning shots into your attacker's chest area before putting a bullet between his eyes. Paraphrased from Louis Awerbuck |
|
![]() |
![]() |
![]() |
#15 |
Foolish Mortal
Join Date: Mar 2007
Location: Livermore, CA
Posts: 243
|
Re: "klunking" when I turn....
Ok, I think I'm gonna enlist my nextdoor neighbor's help on this one-You've all been extremely helpful to the point of me being scared to death because I don't know where to start hehe
I'll let you know when/if I figure it out... |
![]() |
![]() |
![]() |
#16 |
Special Order
![]() ![]() Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,859
|
Re: "klunking" when I turn....
Could be a trailing arm bushing or panhard bar.How does it go down the road?When hitting the gas hard,does it pull to one side?If not,it still could be what I mentioned.A bushing would have to be real bad to effect tracking,but can clunk with just enough wear.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
![]() |
![]() |
![]() |
#17 |
Registered User
Join Date: May 2004
Location: Chandler, AZ
Posts: 519
|
Re: "klunking" when I turn....
I vote for trailing arm bushing, I've rebuilt my suspension, most of what's been suggested, except for these- and I get the same thing.
__________________
![]() ![]() |
![]() |
![]() |
![]() |
#18 |
Senior Member
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
|
Re: "klunking" when I turn....
breeh is exactly right. I wasn't thinking. I replaced mine when I was replacing the whole tranny, so I had to get the crossmember out of there. Hopefully you aren't outside moving the crossmember right now!
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs. |
![]() |
![]() |
![]() |
#19 |
Senior Member
![]() Join Date: Jul 2005
Location: MISSOURI
Posts: 3,256
|
Re: "klunking" when I turn....
Posi or not I'll pick spider gear or axel gear breaking down. Pull the rear cover off and look in there for chipped off peices or other loose metal . My.02%
__________________
The biggest problem people have, is other people Thou shalt be cool and not hassle ![]() Be a site supporter. ![]() The heart of the wise inclines to the right, but the heart of the fool inclines to the left." Ecclesiastes 10:2 |
![]() |
![]() |
![]() |
#20 |
Registered User
Join Date: Jun 2007
Location: TEXAS
Posts: 378
|
Re: "klunking" when I turn....
Grease and add lube oil to everything in sight!
I had the driveshaft making noise in my 91 GMC. I removed it to try to replace the u-joints. They were held in there with some kind of injected plastic. I decided NOT to try to replace them. I just greased them with some newly installed zerks and replaced the shaft. Everything was fine after that. Also, if the clunk is after you put your foot off the brake, you may need to check your tranny modulator. I have replaced that before and it helps smooth things out. Other than that, sounds like broken shocks, shock mounts, missing shock bolts, very worn a-arm bushings or ball joints, etc. Give everything a good look on a lift. |
![]() |
![]() |
![]() |
#21 |
Old Skool Club
![]() Join Date: Jun 2001
Location: Benton, AR "The Heart of Arkansas"
Posts: 10,880
|
Re: "klunking" when I turn....
[QUOTE=LBJ;2663439]Grease and add lube oil to everything in sight!
I had the driveshaft making noise in my 91 GMC. I removed it to try to replace the u-joints. They were held in there with some kind of injected plastic. I decided NOT to try to replace them. I just greased them with some newly installed zerks and replaced the shaft. Everything was fine after that.QUOTE] I was lookin' to see if anyone would mention greasing "stuff". I had a '76 Blazer with a pronounced clunk when stopping/starting. The previous owner was from France, working here to train bellhops at a new hotel, and didn't know we had paved roads in Arkansas, hence the 4WD. The Chevy dealership knew they had a rube in the hand and proceeded to help them spend a couple thousand bucks to "fix" it. Part-time kit in the front end; replaced the inner axle bearings, new torque convertor bolts (left one of them in the nose of the starter....another issue) and replaced the door jamb switches. Clunk still there. It had a set of 10-inch white spokes and 12.00x15's on all four corners and sang like crazy on the highway. Pulled off the wheels/tires. Installed 8-inch wide wheels and 31x11.50's. It's now quieter. Still clunks, but not so bad. Took it for an oil/lube. Greased the slip yokes on the front end, plus all the other lube points. Noise gone. It may not be a lubrication issue, but it's certainly something to be done on a regular basis. Not driving them very often, and those that have been parked for a while, are susceptible to "grease worms" that eat up the grease on your vehicles. Once the "worms" eat all the grease, parts start to wear....or worse. Feed the Grease Worms!!!
__________________
Member Nr. 2770 '96 GMC Sportside; 4.3/SLT - Daily driven....constantly needs washed. '69 C-10 SWB; 350/TH400 - in limbo The older I get, the better I was. |
![]() |
![]() |
![]() |
#22 |
Special Order
![]() ![]() Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,859
|
Re: "klunking" when I turn....
Is there a bottle between the passenger seat and door.That one had me worried until I had someone ride with me and the bottle fell out.My son left it there.
![]() A rear end fluid change is always a good thing.If you can jack a wheel up you can check if it`s a posi.If the raised wheel won`t turn,it`s a posi.If it is a posi and a fluid change w/additive doesn`t cure it I`d look at the bushings in the panhard bar and trailing arms.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
![]() |
![]() |
![]() |
#23 |
laying low
![]() Join Date: Mar 2001
Location: Searcy, Ark. USA
Posts: 13,271
|
Re: "klunking" when I turn....
Yeah, I remember my first time. Not that first time but my first time experiencing the rear end klunk.
![]()
__________________
Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross |
![]() |
![]() |
![]() |
#24 | |
just can't cover up my redneck
Join Date: May 2004
Location: Columbus OH
Posts: 11,414
|
Re: "klunking" when I turn....
Quote:
Also, if you brakes are too tight, this can all be deceiving. What rear end is in the truck? If it is a locker, no amount of "posi additive" will fix it. My initial thought from the OP was brakes. Drums in front? |
|
![]() |
![]() |
![]() |
#25 |
Active Member
Join Date: Jan 2004
Location: Centerville, GA
Posts: 240
|
Re: "klunking" when I turn....
I had a front end "clunk" that eluded me for the longest time. I never could find it so I rebuilt the entire front end. I put it back on the road and the clunk was still there. Come to find out is the tabs on the front disc brake pads were bent out enough to let them move around. It was just enough movement to make a "clunk" when you would stop or go. A little malletization to the tabs where the pads fit tight and no more clunk. Too bad it cost me a couple hundered dollars to figure that one out. On the bright side the tuck has a fresh front end on it...
__________________
Sonny New Project: 67 Small window SWB 2006 Crew Cab Silverado LT ![]() ![]() Last edited by Sonny; 04-06-2008 at 03:40 PM. Reason: spelling |
![]() |
![]() |
![]() |
Bookmarks |
|
|