![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Feb 2008
Location: bay area, CA
Posts: 68
|
3 speed column shifter stuck when it's cold outside
Every morning I go out to start my truck; if it's below about 40 degrees, I can barely pull the shifter up between R-1. Feels like I'm going to bend or break the shifter.
I tried hitting the column with WD40, no luck there. Tried lubing it up with good old grease and still no luck. It seems like the metal is getting cold enough to shrink and bind when it freezes overnight. Is there something I can loosen? Tighten? Lube? My next step was going to be graphite spray.
__________________
1969 ![]() |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Apr 2004
Location: arkieland
Posts: 1,070
|
Re: 3 speed column shifter stuck when it's cold outside
The old grease inside is getting stiff. Only way I know to properly fix it is disassembly of the column, clean out old grease, lube up with fresh stuff.
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Apr 2010
Location: Boise, ID
Posts: 1,280
|
Re: 3 speed column shifter stuck when it's cold outside
My 66 3 on a tree had bushings that I used to lube under the hood on the drivers side that would also bind when going from 1st to 2nd. On my 68 I shot some penetrating lube through where the arm enters the column and it loosened things up. May or may not work.
|
![]() |
![]() |
![]() |
#4 |
Active Member
![]() Join Date: Jul 2007
Location: Centrally located between Houston, Austin and Waco. BCS area.
Posts: 7,947
|
Re: 3 speed column shifter stuck when it's cold outside
There's a long tube that slides up and down the steering column to shift the levers. In the factory it was lathered up with grease which after 40 years dries to a thick sticky substance.
In some cases you can get by spraying the h3ll out of with WD40 or other lubricant/solvent but be sure and protect the floor board and garage floor. In my case I had to take the column off and remove all the old stuff and relube. I had to basically clean out chunks of waxy hard grease.
__________________
68 GMC 250/3 speed Saginaw p/b p/s 69 Chevy 350/350 currently in pieces still lookin for a cab 06 Trailblazer I just want a vehicle that I can work on, that won't talk to me, leave error msgs or keep track of how I drive... |
![]() |
![]() |
![]() |
#5 |
Senior Member
![]() Join Date: Jan 2012
Location: Texan, back in TX
Posts: 2,153
|
Re: 3 speed column shifter stuck when it's cold outside
Good to see this post. I bought my 70 C10 back when it was warm and when the first cold snap came I took the truck out and not being familiar with a 3-on-the-tree, I thought something was broken. But you summed it up perfectly, it seems like I'm going to bend or break the gear shift lever to go from R to 1st. Looks like I need to clean out the old grease on mine too.
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jul 2010
Location: MD
Posts: 1,937
|
Re: 3 speed column shifter stuck when it's cold outside
x3 three on old column grease. My 3 tree used to do that.
A Hurst floor shift conversion kit solved it quite nicely. ![]()
__________________
1969 c-10 Step Side Long Bed. I-6 250cid = ![]() |
![]() |
![]() |
![]() |
#7 |
Senior Member
![]() Join Date: Jan 2012
Location: Texan, back in TX
Posts: 2,153
|
Re: 3 speed column shifter stuck when it's cold outside
Hey , thewrai6th I ran across this thread http://67-72chevytrucks.com/vboard/s...d.php?t=215307 and it seems to have some good 3OTT info. Check out the 3rd sentence of the original post.
|
![]() |
![]() |
![]() |
Bookmarks |
Tags |
3 on the tree, shifter, stuck |
|
|