Heater hoses..... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dubie · 06-25-2003, 03:33 PM

Does anyone have pics of the 2 hoses that come from your heater box? I need to know where they go to. 1 of them goes to a sensor on my intake but where does the other go?

bpmcgee · 06-25-2003, 03:41 PM

On my 71 blazer, the top one goes to the top of the intake manifold and the other goes to the top passengers side port on the radiator.

Brian

dubie · 06-25-2003, 03:51 PM

I don't have a port on the side of my rad for the second hose. I have a plug in the top of the water pump on this 350 and it looks like there should be a hose go onto there. HELP!?!?!?

tom hand · 06-25-2003, 03:53 PM

It should go to the side if the waterpump...right above the radiator hose

dubie · 06-25-2003, 04:20 PM

I know the one on the intake is for one of the hoses, but i think the other goes where that plug is on top of the water pump.

**CPNE** · 06-25-2003, 04:25 PM

This does not show it too good because a fan blade is partially in the way but, here's how it should go

**CPNE** · 06-25-2003, 04:27 PM

better view

dubie · 06-25-2003, 04:29 PM

I don't have a port there

**CPNE** · 06-25-2003, 04:34 PM

See! What did I tell you about not following the manufacturers recommended installation? See! I told you so! If you'd done it by the book it'd be done now! No fuss no muss. Now you're f__ked

Seriously, can't help ya now. Maybe with that pump they were figuring you'd have a place to connect on the radiator?

dubie · 06-25-2003, 04:40 PM

This engine is from an 82 Chevy van. So it wouldn't go where that plug is on the top pic I posted? It also goes into the water pump?

Longhorn Man · 06-25-2003, 04:40 PM

You can take your rad to a shop and they could install the fitting you need. Most should have the stuff on hand, and it'll only cost a few bucks. Figure one hr of labor.
Can't go without heat up there.

SEVEND2 · 06-25-2003, 04:44 PM

CPNE- Mine are just oposite of that my top one goes to the block and lower one goes to the Rad nipple, I might have my core upside down though

**CPNE** · 06-25-2003, 04:46 PM

That one may be too. Anyway I don't think it matters too much as the pump is pushing it through no matter what.

dubie · 06-25-2003, 04:54 PM

So as long as 1 of these hoses is coming from the water pump I should be OK? I am sorry if these are kinda dumbass questions but this is my first engine build up

SEVEND2 · 06-25-2003, 05:11 PM

you need a in and out!

andyr354 · 06-25-2003, 05:12 PM

There are two main styles of chevy water pumps. The older short pump will have the port on it for the return of the heater core. the newer long pump setup dumped into the radiator for return. Problem is if you go to a short pump none of your brackets will work, they are different.

tom hand · 06-25-2003, 05:13 PM

Try it and let us know

**68 Stepside** · 06-25-2003, 05:26 PM

Are BB's and SB's the same?? (I really don't know... :\)

Low68 · 06-25-2003, 05:35 PM

Hey dubbie, That plug was right on top of your water pump right? On mine, it used there used to be one out of the top of the water pump and one out of the manifold. Like someone else said, I don't think it matter that much which hoses go where though. Good luck.
Low68

dubie · 06-25-2003, 06:15 PM

anyone have pics of the fitting on the rad? Just so I know where it goes? So many different opinions here. Does anyone know for sure if i can just use the plug on the top of the water pump?

**old Rusty C10** · 06-25-2003, 06:24 PM

see post onm 73 -87 message board

**68 Stepside** · 06-25-2003, 09:04 PM

Yes, you can

dubie · 06-25-2003, 10:02 PM

OK, a buddy of mine just bought a 69 long fleet tonight and it has a 305 in it with the same set up. And YES , I can remove that plug on the top of the water pump and run the 2nd hose through there. Finally my mind is set at ease. Thanks for all the great info guys

06-25-2003, 03:33 PM	#1
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,855	Heater hoses..... Does anyone have pics of the 2 hoses that come from your heater box? I need to know where they go to. 1 of them goes to a sensor on my intake but where does the other go? __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

06-25-2003, 03:51 PM	#3
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,855	I don't have a port on the side of my rad for the second hose. I have a plug in the top of the water pump on this 350 and it looks like there should be a hose go onto there. HELP!?!?!? __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

06-25-2003, 03:53 PM	#4
tom hand CCRider Join Date: Feb 2000 Location: Olive Branch,MS,USA Posts: 2,232	It should go to the side if the waterpump...right above the radiator hose __________________ 72 GMC Sierra SWB almost finished---- 84 Softail Olive Branch MS

06-25-2003, 04:20 PM	#5
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,855	I know the one on the intake is for one of the hoses, but i think the other goes where that plug is on top of the water pump. __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

06-25-2003, 04:25 PM	#6
CPNE Resident Curmudgeon Join Date: Dec 1999 Location: NH Posts: 6,664	This does not show it too good because a fan blade is partially in the way but, here's how it should go Attached Images __________________ Currently on or near the homestead: 67 Chevy SWB 2WD stepside 350/3 on tree (Pat's) 67 GMC SWB 2WD Fleet 402/auto (Brian's under construction) 67 Chevy 3/4 ton 2WD 402/auto (Business Hauler) 67 Chevy 1 ton dually 2WD 396/4 speed (Former business hauler, Needs TLC) 68 Chevy 1/2 ton Suburban 2WD 250 six/3 on tree (Brian's Needs TLC) 70 Chevy 3/4 ton 4WD 350/4 speed (Pat's - Disguised as a 68 GMC) 71 Chevy SWB stepside (Crushed by tree - parts donor) 72 Chevy 3/4 ton 4WD (Parts donor) 72 Chevy 3/4 ton 4WD Suburban (Parts Donor) 72 GMC 3/4 ton 4WD 292 six/4 speed (Mine - Disguised as a 67 GMC) 81 GMC 4WD Dually Dump Body 350/4 speed (Business Hauler) 82 Camaro Z/28 355/Super T-10 (Pat's toy) 93 Caprice 9C1 (Brian's Cop Car) 02 Toyota Camry (Reliable but a souless steel and plastic hulk) 2011 2SS RS Camaro M6 Factory Hurst Shifter Maybe I need to sell some of this crap Yet another Bozo with a sawz-all

06-25-2003, 03:41 PM	#2
bpmcgee Registered User Join Date: Mar 2003 Location: Northern Illinois Posts: 2,181	On my 71 blazer, the top one goes to the top of the intake manifold and the other goes to the top passengers side port on the radiator. Brian

06-25-2003, 04:27 PM	#7
CPNE Resident Curmudgeon Join Date: Dec 1999 Location: NH Posts: 6,664	better view Attached Images __________________ Currently on or near the homestead: 67 Chevy SWB 2WD stepside 350/3 on tree (Pat's) 67 GMC SWB 2WD Fleet 402/auto (Brian's under construction) 67 Chevy 3/4 ton 2WD 402/auto (Business Hauler) 67 Chevy 1 ton dually 2WD 396/4 speed (Former business hauler, Needs TLC) 68 Chevy 1/2 ton Suburban 2WD 250 six/3 on tree (Brian's Needs TLC) 70 Chevy 3/4 ton 4WD 350/4 speed (Pat's - Disguised as a 68 GMC) 71 Chevy SWB stepside (Crushed by tree - parts donor) 72 Chevy 3/4 ton 4WD (Parts donor) 72 Chevy 3/4 ton 4WD Suburban (Parts Donor) 72 GMC 3/4 ton 4WD 292 six/4 speed (Mine - Disguised as a 67 GMC) 81 GMC 4WD Dually Dump Body 350/4 speed (Business Hauler) 82 Camaro Z/28 355/Super T-10 (Pat's toy) 93 Caprice 9C1 (Brian's Cop Car) 02 Toyota Camry (Reliable but a souless steel and plastic hulk) 2011 2SS RS Camaro M6 Factory Hurst Shifter Maybe I need to sell some of this crap Yet another Bozo with a sawz-all

06-25-2003, 04:29 PM	#8
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,855	I don't have a port there __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

06-25-2003, 04:34 PM	#9
CPNE Resident Curmudgeon Join Date: Dec 1999 Location: NH Posts: 6,664	See! What did I tell you about not following the manufacturers recommended installation? See! I told you so! If you'd done it by the book it'd be done now! No fuss no muss. Now you're f__ked Seriously, can't help ya now. Maybe with that pump they were figuring you'd have a place to connect on the radiator? __________________ Currently on or near the homestead: 67 Chevy SWB 2WD stepside 350/3 on tree (Pat's) 67 GMC SWB 2WD Fleet 402/auto (Brian's under construction) 67 Chevy 3/4 ton 2WD 402/auto (Business Hauler) 67 Chevy 1 ton dually 2WD 396/4 speed (Former business hauler, Needs TLC) 68 Chevy 1/2 ton Suburban 2WD 250 six/3 on tree (Brian's Needs TLC) 70 Chevy 3/4 ton 4WD 350/4 speed (Pat's - Disguised as a 68 GMC) 71 Chevy SWB stepside (Crushed by tree - parts donor) 72 Chevy 3/4 ton 4WD (Parts donor) 72 Chevy 3/4 ton 4WD Suburban (Parts Donor) 72 GMC 3/4 ton 4WD 292 six/4 speed (Mine - Disguised as a 67 GMC) 81 GMC 4WD Dually Dump Body 350/4 speed (Business Hauler) 82 Camaro Z/28 355/Super T-10 (Pat's toy) 93 Caprice 9C1 (Brian's Cop Car) 02 Toyota Camry (Reliable but a souless steel and plastic hulk) 2011 2SS RS Camaro M6 Factory Hurst Shifter Maybe I need to sell some of this crap Yet another Bozo with a sawz-all

06-25-2003, 04:40 PM	#10
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,855	This engine is from an 82 Chevy van. So it wouldn't go where that plug is on the top pic I posted? It also goes into the water pump? __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

06-25-2003, 04:40 PM	#11
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	You can take your rad to a shop and they could install the fitting you need. Most should have the stuff on hand, and it'll only cost a few bucks. Figure one hr of labor. Can't go without heat up there.

06-25-2003, 04:44 PM	#12
SEVEND2 Registered User Join Date: Aug 2001 Location: Menifee, Calif, USA Posts: 2,145	CPNE- Mine are just oposite of that my top one goes to the block and lower one goes to the Rad nipple, I might have my core upside down though __________________ With a 1972 Chevy Custom-10 Long bed w/350cid th350, (under-construction). Progress on truck so far (follow link): http://67-72chevytrucks.com/vboard/s...ad.php?t=51051 and stage 2 http://67-72chevytrucks.com/vboard/s...ad.php?t=58132 ~ "Why couldn't you have just put the bunny back in the box?" ~

06-25-2003, 04:46 PM	#13
CPNE Resident Curmudgeon Join Date: Dec 1999 Location: NH Posts: 6,664	That one may be too. Anyway I don't think it matters too much as the pump is pushing it through no matter what. __________________ Currently on or near the homestead: 67 Chevy SWB 2WD stepside 350/3 on tree (Pat's) 67 GMC SWB 2WD Fleet 402/auto (Brian's under construction) 67 Chevy 3/4 ton 2WD 402/auto (Business Hauler) 67 Chevy 1 ton dually 2WD 396/4 speed (Former business hauler, Needs TLC) 68 Chevy 1/2 ton Suburban 2WD 250 six/3 on tree (Brian's Needs TLC) 70 Chevy 3/4 ton 4WD 350/4 speed (Pat's - Disguised as a 68 GMC) 71 Chevy SWB stepside (Crushed by tree - parts donor) 72 Chevy 3/4 ton 4WD (Parts donor) 72 Chevy 3/4 ton 4WD Suburban (Parts Donor) 72 GMC 3/4 ton 4WD 292 six/4 speed (Mine - Disguised as a 67 GMC) 81 GMC 4WD Dually Dump Body 350/4 speed (Business Hauler) 82 Camaro Z/28 355/Super T-10 (Pat's toy) 93 Caprice 9C1 (Brian's Cop Car) 02 Toyota Camry (Reliable but a souless steel and plastic hulk) 2011 2SS RS Camaro M6 Factory Hurst Shifter Maybe I need to sell some of this crap Yet another Bozo with a sawz-all

06-25-2003, 04:54 PM	#14
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,855	So as long as 1 of these hoses is coming from the water pump I should be OK? I am sorry if these are kinda dumbass questions but this is my first engine build up __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

06-25-2003, 05:11 PM	#15
SEVEND2 Registered User Join Date: Aug 2001 Location: Menifee, Calif, USA Posts: 2,145	you need a in and out! __________________ With a 1972 Chevy Custom-10 Long bed w/350cid th350, (under-construction). Progress on truck so far (follow link): http://67-72chevytrucks.com/vboard/s...ad.php?t=51051 and stage 2 http://67-72chevytrucks.com/vboard/s...ad.php?t=58132 ~ "Why couldn't you have just put the bunny back in the box?" ~



Register or Log In To remove these advertisements.

06-25-2003, 05:12 PM	#16
andyr354 Registered User Join Date: Mar 2003 Location: Mahaska, KS Posts: 82	There are two main styles of chevy water pumps. The older short pump will have the port on it for the return of the heater core. the newer long pump setup dumped into the radiator for return. Problem is if you go to a short pump none of your brackets will work, they are different. __________________ 1970 C10: 2WD, LWB, 350, 350 auto, Headers, Duals, Edelbrock 1406 with 2101 intake, and optional rust.

06-25-2003, 05:13 PM	#17
tom hand CCRider Join Date: Feb 2000 Location: Olive Branch,MS,USA Posts: 2,232	Try it and let us know __________________ 72 GMC Sierra SWB almost finished---- 84 Softail Olive Branch MS

06-25-2003, 05:26 PM	#18
68 Stepside huh? Join Date: May 2000 Location: Washington, Illinois Posts: 5,692	Are BB's and SB's the same?? (I really don't know... :\) __________________ Someday when I'm lonely, Wishing you weren't so far away, Then I will remember Things we said today. RIP El Jay

06-25-2003, 05:35 PM	#19
Low68 Registered User Join Date: May 2001 Location: Arizona Posts: 758	Hey dubbie, That plug was right on top of your water pump right? On mine, it used there used to be one out of the top of the water pump and one out of the manifold. Like someone else said, I don't think it matter that much which hoses go where though. Good luck. Low68 __________________ Build Thread

06-25-2003, 06:15 PM	#20
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,855	anyone have pics of the fitting on the rad? Just so I know where it goes? So many different opinions here. Does anyone know for sure if i can just use the plug on the top of the water pump? __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

06-25-2003, 06:24 PM	#21
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,307	see post onm 73 -87 message board __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

06-25-2003, 09:04 PM	#22
68 Stepside huh? Join Date: May 2000 Location: Washington, Illinois Posts: 5,692	Yes, you can __________________ Someday when I'm lonely, Wishing you weren't so far away, Then I will remember Things we said today. RIP El Jay

06-25-2003, 10:02 PM	#23
dubie Registered User Join Date: May 2000 Location: Flin Flon, Manitoba, Canada Posts: 8,855	OK, a buddy of mine just bought a 69 long fleet tonight and it has a 305 in it with the same set up. And YES , I can remove that plug on the top of the water pump and run the 2nd hose through there. Finally my mind is set at ease. Thanks for all the great info guys __________________ My name's Tim and I'm a truckaholic My 56 Chevy shop truck build http://67-72chevytrucks.com/vboard/s...d.php?t=562795

Register or Log In To remove these advertisements.