Folding Bench Seat for '69 C/10 ?

[VWNate1]

O.K. , I tried the search engine and didn't find anything .

I need a folding backrest stock bench seat for my '69 C/10 , before I go buy the wrong one from a '72 , do they all interchange from '67 ! '72 ? .

I hope to buy a good used folding bench and have it re covered, they
re really cheap in all the scrap yards once the covers are gone .

Don't waste time telling me to simply remove the rear most side bolt on each backrest support , that's not going to work , I read that B.S. here before and took my nice original seat apart , I need a true folder with a pivot , not junk .

TIA ,

[Shyguy]

No B.S. here. The only stock fold down back seats I have seen were from a '67 or early '68.

Hope this helps.

[69C-owner]

hmm didnt know they made them but I'm guessing all 6 years had the same bolt pattern for the seat mounts so if you find one thats in a 67-72 then id say it will fit in your 69 but dont hold me to that

[70STOVEBOLT]

I thought they were all folding, since the gas tank is behind there. I bought mine from a local guy but idk what year it's out of.

[leddzepp]

All 67-72 bench seats will interchange, as they have the same mounting brackets. I have found the only ones that fold forward however have been out of 67-68 trucks. And you are right, there are a ton of them at the junkyards here.

[Classic Bowties]

Originally Posted by VWNate1

O.K. , I tried the search engine and didn't find anything . I need a folding backrest stock bench seat for my '69 C/10 , before I go buy the wrong one from a '72 , do they all interchange from '67 ! '72 ? .

As shyguy and ledd have already stated above, look for an original bench out of a 67 or 68.

Originally Posted by leddzepp

All 67-72 bench seats will interchange, as they have the same mounting brackets.

Ledd, that first part is true as they all used the same overall mounting footprint, but on that second part it should be noted that the lower bench frames and bench mounting bracket & track height changed between 67-72 at least twice if not three times (I would need to dig around a bit to confirm a third). Mel

[leddzepp]

Originally Posted by Classic Bowties

Ledd, that first part is true as they all used the same overall mounting footprint, but on that second part it should be noted that the lower bench frames and bench mounting bracket & track height changed between 67-72 at least twice if not three times (I would need to dig around a bit to confirm a third). Mel

Thanks for the clarification Mel. I know the brackets themselves had some differences, but I just wanted to get the point across that all bench brackets will bolt to the floor regardless of the year. If you have a pic depicting the differences, that would be awesome info.

[VWNate1]

As I don't see many '67 /'68's in my local yards , I'll just keep an eye out ~

I looked at those nice repop original typ covers and have decided to custom rebuild me a nice rock hard one , I have a broken back so a firm seat , no foam , is very important .

I'll get on the search , anyone in the So. Cal. area who spots one in a Pick-A-part give me a shout and I'll grab it .

My '76 GMC came with the ridgid backrest , I found an '83 with the folder and grabbed it , the floor mounts were the same so that was possibly the best $35 I spent on that truck .

Again , THANK YOU for the help ! I'm a dedicated InLiner guy so I hope I can return the help , I can tune these old beasts to run very sweetly indeed .

[Baggerjohn]

I'm taking out a seat like you're describing out of my 67. It's in fairly good condition. Hopefully I will have it out in the next two weeks. It is black. Has a tear along the seam on drivers side. Other than that, it's all good. I'm in Huntington Beach if you care to see it.

[VWNate1]

Originally Posted by Baggerjohn

I'm taking out a seat like you're describing out of my 67. It's in fairly good condition. Hopefully I will have it out in the next two weeks. It is black. Has a tear along the seam on drivers side. Other than that, it's all good. I'm in Huntington Beach if you care to see it.

YES PLEASE ! .

Ping me off list to arrange this please : VWNate1 (at) yahoo,com .

THANX !

[1972RedNeck]

The '67 seat I have has springs and foam in the back. Could you get a full foam seat in '67?

[_Ogre]

nate good to see you over here.
lot's of activity on this forum.
hope you found a new home here...

[VWNate1]

Any time I find InLine enthusiasts , I'm home .

Seems like a good bunch here .

[lil hoodlum]

Nice looking truck!

Are those Texas plates on there? Looks like some Texas Registration and safety inspections stickers on the windshield also.

Good luck!

Keith

[VWNate1]

Yes ~ this was a Ranch truck somewhere in TEXAS , I was unable to find any shortbed L6 powered trucks in So. Cal., prolly they all got Hot Rodded years back .

I found it in Dallas , bought it and drove it home via those wonderful two lane blacktop roads it was made to run , I love touring America in my oldies , I do not own a modern car or truck .

As the mechanicals are somewhat suspect , it took me nearly a whole case of oil to get it home but I'm working on sorting it out whilst continuing to drive , work and enjoy it very much ~ a typical GM product , it can be seriously neglected or abused and still be everything one ever wanted in a truck . that's why I'm a Bowtie Guy 'till I die ! .

The paint is actually rather weathered , I'm not sure what kinda wax they used but I wish I did ! . it looked terrific if suspect , as soon as that wax wore off , it looks like just another old truck .

I've only had it since August last year and already nearly 10,000 miles on it .

[lil hoodlum]

Well I think you have a rather neat truck. I'm not the biggest fan of the wagon wheels but I think they look good on your truck.

Wow! A whole case of oil!?! Did you have any problems on the drive to California? I would be interested to hear about your trip home.

Thanks for sharing.

By the way, my seat is out of a 1968 GMC and it does fold forward. I may be incorrect but I believe all of the bench seats from 1967-1972 will fold forward if the wingnut(s) are removed. The bench seat covers from the 1969 and up usually have a covering over the mechanism that will allow the seat back to fold forward.

[leddzepp]

In order to post any item for sale you must be a subscribing member. here is info on how to do that: http://67-72chevytrucks.com/vboard/payments.php

If that link does not work, click on "subscribe" near the top of this page, just under the search box

[VWNate1]

Thanx ! .

[VWNate1]

O-Kay then ;

Dano's Yard Sale set me up with a nice old '67 folding back rest bench seat , I took it to PerezAuto Trimmers in Pasadena (626) 700.7945 , he did a nice job of rebuilding it and I had him enclose the back part & add three large pockets to it so now I have a place for my map book , windshield sun shade , etc. etc. .

It's nice and firm too ~ just the thing for an old man's broken back .

I gave the old seat in VGC to ' 50BOMB ' , he's in Garden Grove if anyone would be so kind as to carry it down there to him....

[Red68]

I wanted a full foam seat (back and bottom) that also folded forward. Learned that it was not an option so I took my old spring back seat and found a full foam back seat cut the bottom part that hinges off my spring seat and welded on the foam back frame along with the stops. It is at the upholstery shop right now getting covered.

I'll post some pics when I get it back.

Kevin

[VWNate1]

Sounds good ! .

Please remember to post pictures here when it's done , weather it turns out good or bad .

[Red68]

Here is a couple pictures of my new foam back folding seat. Turned out great! Doesnt fold as far forward as the old seat but still works the way I want it to.

The guy who did the seat cut off the radius piece from the old spring back seat and welded it on the back of the foam seat frame. I cut off the "ears" from the old spring bottom seat that the seat back rests on and they welded it onto the new foam bottom seat frame.

[VWNate1]

VERY nice ! .

I like the dip in the center top stitching line .

[Dano69c10]

Hey Nate, can we get pics of your folding bench seat?

[RenoKeene]

And yes, we would like to hear road stories. Pleeeeeese