|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
06-14-2010, 03:56 PM
|
#1 |
|
Registered User
Join Date: May 2010
Location: USA
Posts: 18
|
pressure plate change. 72 jimmy
ok my next problem is the pressure plate is not realeasing. If I have to change this do I have to come in from inside the cab? I notice there is an access cover over the trans and transfer box.
Or is it not worth the hassle and just have the shop do it. ? |
|
|
|
06-14-2010, 08:26 PM
|
#2 |
|
I'm a poor spectator
Join Date: Aug 2006
Location: San Antonio, Tx
Posts: 2,287
|
Re: pressure plate change. 72 jimmy
It's pretty easy. The only part I needed help with was when I was putting the tranny/xfercse back in. It was just kind of akward to get it back up there by myself.
__________________
2006 Jeep Unlimited IMPACT ORANGE 1993 Chevy 2500 4x4 ExCab LWB 454/NV4500 Tow rig  1977 Ford F100 2x4 LWB 1st truck I owned, still have it!!!  1979 Ford F150 4x4 SWB Built Ford Tough!!!  1971 Chevy Blazer 350 / SM465 / NP205 UNDER CONSTRUCTION Soon to have a LQ4 6.0!!! |
|
|
|
|
06-14-2010, 09:51 PM
|
#3 |
|
Registered User
Join Date: May 2010
Location: USA
Posts: 18
|
Re: pressure plate change. 72 jimmy
I was thinking about pulling the motor instead. Then at least I can pressure wash it.. However Ive never done this model before. last thing I want to deal with is nasty gear oil !
|
|
|
|
|
06-14-2010, 11:47 PM
|
#4 |
|
I'm a poor spectator
Join Date: Aug 2006
Location: San Antonio, Tx
Posts: 2,287
|
Re: pressure plate change. 72 jimmy
If you've never done it it's easy to pull it but putting it back in usually will require a little help to man the hoist while you or your friend is under the truck lining up the transmission main shaft into the back of the engine.
__________________
2006 Jeep Unlimited IMPACT ORANGE 1993 Chevy 2500 4x4 ExCab LWB 454/NV4500 Tow rig 1977 Ford F100 2x4 LWB 1st truck I owned, still have it!!! 1979 Ford F150 4x4 SWB Built Ford Tough!!! 1971 Chevy Blazer 350 / SM465 / NP205 UNDER CONSTRUCTION Soon to have a LQ4 6.0!!! |
|
|
|
|
06-15-2010, 02:33 PM
|
#5 |
|
I miss this truck.
Join Date: Dec 2001
Location: Lexington, KY U.S.A.
Posts: 2,863
|
Re: pressure plate change. 72 jimmy
Pulling the motor, replacing the pressure plate, and re-installing the motor could reasonably be accomplished in a day with 2 guys. Quicker if you have air tools.
__________________
'07 GMC Acadia SLT. Sweet ride. '08 Crew Cab Z-71 short bed. Really like this truck A LOT. |
|
|
|
|
06-16-2010, 05:45 PM
|
#6 |
|
Registered User
Join Date: May 2010
Location: USA
Posts: 18
|
Re: pressure plate change. 72 jimmy
ok got the seats pulled out, and the shell over the tranny removed.
Would it be easier to pull the motor and change the clutch assy or pull the tranny and T-box. I power washed the engine so its a bit cleaner. Or do I remove the drive shafts unbolt the the 4sp from the bell housing and move everything aft. then change the clutch assy...? |
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
