Installed AVS Shaved Door Kit - The 1947 - Present Chevrolet & GMC Truck Message Board Network

AusTx68 · 04-30-2011, 10:52 PM

After looking at shaved door kits I went with a 4 channel kit from AVS. I picked it up from ridinglowcustoms.com for $150. Came with dual actuators, wiring harness and key fobs. The photo is of the 8 channel kit but it looks the same. I searched this forum for actuator install photos but didn't see any so I thought to share how I mounted mine.

AVS makes a 4, 8, and 12 channel kit. I only needed it for my doors so 4 channels was 2 too many. Leaves me room for creativity later

The install was pretty straight forward. I started on the drivers door which took twice as long to install because I had to determine actuator location and figure out how to run the cables. Speaking of cables, this kit replaces the stock door rods with a cable to the latch and inside door handle. You still use the inside door handle to get out. As you can see in the photo I mounted the actuator across the inner hole of the door using brackets that came with the kit. This location leaves plenty of room for window operation. There's an optional cable guide to keep the wire from laying on the actuator (shown). Once I got the actuators in place the rest was easy thanks to the wiring harness. Just plug it all up and run the power. It opened the door on the first try but wouldn't fully close. I loosen the cable in the actuator and it fixed the problem. During testing the doors opened nicely. I have new door rubber so there is plenty pressure to push open the door without the need for pushers.

Overall the install was quick and simple. I'm definitely happy with it. If you are looking to do the same I hope this posting helps.

The bracket on the right is only mounted on the bottom which is why I put two screws.

colin_havens · 05-02-2011, 11:41 AM

Nice job! Did you switch to bearclaw latches as well, or use the origional ones? i have heard you had to switch, so I havent even looked into doing this when I repaint due to the additional cost.

Tim R · 05-02-2011, 11:59 AM

I Agree nice joband thanks for the information . I am ordering the same kit this week . Glad to know it works well . I have really been worrying about which kit to buy. I was leaning towards this one because of the dual motors.

Thanks Tim

Gobbles · 05-02-2011, 01:10 PM

You have a gorgeous truck, also interested if you used bear claws!

AusTx68 · 05-02-2011, 05:25 PM

Nope, didn't use bear claws. The stock latch worked fine. I simply connected the cable where the rod used to be and it opens with no issues.

Aggie Daddy · 05-02-2011, 05:42 PM

Thanks for the info.

Very clean truck, except one problem....that orange color.
A nice Aggie maroon would look great.

I'm just kiddin Austin, TX. A very nice truck.

AusTx68 · 05-02-2011, 10:20 PM

Quote:

Originally Posted by West Texas Z

impressive. Video of it functioning?

Not till the weekend.

Quote:

Originally Posted by Aggie Daddy

Thanks for the info.

Very clean truck, except one problem....that orange color.
A nice Aggie maroon would look great.

I'm just kiddin Austin, TX. A very nice truck.

And I'm not even a Longhorn or a fan! I just happen to live here but the locals love the color

Btw..Go Tech!!

West Texas Z · 05-04-2011, 11:59 AM

Quote:

Originally Posted by AusTx68

Not till the weekend.

And I'm not even a Longhorn or a fan! I just happen to live here but the locals love the color

Btw..Go Tech!!

West Texas Z · 05-02-2011, 05:33 PM

impressive. Video of it functioning?

AusTx68 · 05-13-2011, 08:45 PM

Quote:

Originally Posted by West Texas Z

impressive. Video of it functioning?

Finally got around to making that video..here ya go!

YouTube - AVS Shaved Door Kit on 68' C-10

04-30-2011, 10:52 PM	#1
AusTx68 Registered User Join Date: Nov 2008 Location: Italy Posts: 1,278	Installed AVS Shaved Door Kit After looking at shaved door kits I went with a 4 channel kit from AVS. I picked it up from ridinglowcustoms.com for $150. Came with dual actuators, wiring harness and key fobs. The photo is of the 8 channel kit but it looks the same. I searched this forum for actuator install photos but didn't see any so I thought to share how I mounted mine. AVS makes a 4, 8, and 12 channel kit. I only needed it for my doors so 4 channels was 2 too many. Leaves me room for creativity later The install was pretty straight forward. I started on the drivers door which took twice as long to install because I had to determine actuator location and figure out how to run the cables. Speaking of cables, this kit replaces the stock door rods with a cable to the latch and inside door handle. You still use the inside door handle to get out. As you can see in the photo I mounted the actuator across the inner hole of the door using brackets that came with the kit. This location leaves plenty of room for window operation. There's an optional cable guide to keep the wire from laying on the actuator (shown). Once I got the actuators in place the rest was easy thanks to the wiring harness. Just plug it all up and run the power. It opened the door on the first try but wouldn't fully close. I loosen the cable in the actuator and it fixed the problem. During testing the doors opened nicely. I have new door rubber so there is plenty pressure to push open the door without the need for pushers. Overall the install was quick and simple. I'm definitely happy with it. If you are looking to do the same I hope this posting helps. The bracket on the right is only mounted on the bottom which is why I put two screws. __________________ '68 C-10 SWB 383 Stroker (Sold 3/2/2013) '87 R2500 LWB 454 TBI converted to Carb

05-02-2011, 11:41 AM	#2
colin_havens Registered User Join Date: Dec 2007 Location: Mountain Home, AR Posts: 405	Re: Installed AVS Shaved Door Kit Nice job! Did you switch to bearclaw latches as well, or use the origional ones? i have heard you had to switch, so I havent even looked into doing this when I repaint due to the additional cost.

05-02-2011, 11:59 AM	#3
Tim R Registered User Join Date: Jan 2009 Location: bmt,tx Posts: 127	Re: Installed AVS Shaved Door Kit I Agree nice joband thanks for the information . I am ordering the same kit this week . Glad to know it works well . I have really been worrying about which kit to buy. I was leaning towards this one because of the dual motors. Thanks Tim

05-02-2011, 01:10 PM	#4
Gobbles Registered User Join Date: Sep 2010 Location: British Columbia Posts: 484	Re: Installed AVS Shaved Door Kit You have a gorgeous truck, also interested if you used bear claws! __________________ Trevor "You already said spite"

05-02-2011, 05:25 PM	#5
AusTx68 Registered User Join Date: Nov 2008 Location: Italy Posts: 1,278	Re: Installed AVS Shaved Door Kit Nope, didn't use bear claws. The stock latch worked fine. I simply connected the cable where the rod used to be and it opens with no issues. __________________ '68 C-10 SWB 383 Stroker (Sold 3/2/2013) '87 R2500 LWB 454 TBI converted to Carb

05-02-2011, 05:42 PM	#6
Aggie Daddy Registered User Join Date: Jan 2011 Location: Bryan, TX Posts: 1	Re: Installed AVS Shaved Door Kit Thanks for the info. Very clean truck, except one problem....that orange color. A nice Aggie maroon would look great. I'm just kiddin Austin, TX. A very nice truck.

05-02-2011, 05:33 PM	#9
West Texas Z El Mero Mero Frijolero!! Join Date: Mar 2010 Location: Lubbock, Texas Posts: 669	Re: Installed AVS Shaved Door Kit impressive. Video of it functioning? __________________ My Toys: 1993 Ford Mustang LX 5.0 2001 Yamaha V Star 650 1984 Silverado > Build Page <



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.