T-case rattles at 60 MPH...suggestions - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Daubs** · 02-21-2005, 01:14 PM

It's a mutt (body from C20, frame and running gear from K20) 350 with 4 speed manual and I believe the 205 t-case. Shifts in and out of 4hi and 4low well.

When I approach 60 MPH the t-case shift lever starts to vibrate and make noise. Gets louder as I increase speed. Sounds like the linkage is rattling more than anything else. Suggestions?

I can certainly live with this because the truck isn't my daily driver. Wondering if I've got a slight kink in a shaft causing a little wobble. Or bad bearing in the case?

86SILVERADO · 02-21-2005, 01:20 PM

Well When I approach 60mph in the 67 Everything in and on the truck starts to vibrate and make noise.

I would check the easy stuff first like slop between the shift column and shaft on the t-case. Mounts and U-joints.

71swb4x4 · 02-21-2005, 02:06 PM

My shifter rattles too. I think a new shifter boot may hold it enough to keep it from rattling, but I am not sure. Let us know what you figure out.

da-burb · 02-21-2005, 02:29 PM

I have the same thing. I know when I am doing 55mph by the rattle. The short term fix is to put something over it like a mitten, welding glove, heavy rag. I didn't believe it would work, but it does. Matt Rein told me this trick a few years ago and I have used it since.

72 Cheyenne K20 · 02-21-2005, 02:30 PM

I had the same prob with a 70 k20. PO use the wrong size bolt and no washers to hold the shifter. Replaced with correct bolt and washers and was tight as new.

Scott

**Daubs** · 02-21-2005, 03:30 PM

I was wondering about washers and bolts for the shifter. I'll check into that. Thanks. The boot is cracked and I can see the cement through it. Replacement coming as soon.

Yes, it is a 30+ year old truck, and it's going to rattle and shake. I'm amazed that it doesn't sound worse than it does...I'm thinking the PO took good care of this ride.

02-21-2005, 01:14 PM	#1
Daubs Registered User Join Date: Jan 2005 Location: Eastern Nebraska Posts: 611	T-case rattles at 60 MPH...suggestions It's a mutt (body from C20, frame and running gear from K20) 350 with 4 speed manual and I believe the 205 t-case. Shifts in and out of 4hi and 4low well. When I approach 60 MPH the t-case shift lever starts to vibrate and make noise. Gets louder as I increase speed. Sounds like the linkage is rattling more than anything else. Suggestions? I can certainly live with this because the truck isn't my daily driver. Wondering if I've got a slight kink in a shaft causing a little wobble. Or bad bearing in the case? __________________ '72 Chevy K-20 Crate 350, SM465, 4.10's

02-21-2005, 01:20 PM	#2
86SILVERADO Registered User Join Date: Dec 2002 Location: Hills of Western Mass Posts: 626	Well When I approach 60mph in the 67 Everything in and on the truck starts to vibrate and make noise. I would check the easy stuff first like slop between the shift column and shaft on the t-case. Mounts and U-joints. __________________ 86 Silverado C10 back to 305 power! 67 C30 Dually Dump, with 350 transplant, Rockhauler 05 Duramax 3500 "If at first you don't succeed, try a bigger hammer" Member of the 1-Ton club!

02-21-2005, 02:06 PM	#3
71swb4x4 Senior Member Join Date: Nov 2003 Location: Brookings, SD Posts: 10,497	My shifter rattles too. I think a new shifter boot may hold it enough to keep it from rattling, but I am not sure. Let us know what you figure out. __________________ Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs.

02-21-2005, 02:29 PM	#4
da-burb "Ochre Ogre" Join Date: Apr 2000 Location: Springfield, MN Posts: 3,558	I have the same thing. I know when I am doing 55mph by the rattle. The short term fix is to put something over it like a mitten, welding glove, heavy rag. I didn't believe it would work, but it does. Matt Rein told me this trick a few years ago and I have used it since. __________________ Bowtie Truck Stop Inc. Mid-West GM Truck Restoration Parts Supplier Your Key Parts, Auto Metal Direct, Dynacorn, and Goodmark dealer. like us @ www.facebook.com/BowtieTruckStop 1971 C-10 Suburban (Ochre) 1971 K-10 Suburban (Ochre) 1972 C-10 Suburban (Ochre) 1972 K-20 Suburban (Yellow- that just aint right!) Springfield, Minnesota 56087

02-21-2005, 03:30 PM	#6
Daubs Registered User Join Date: Jan 2005 Location: Eastern Nebraska Posts: 611	I was wondering about washers and bolts for the shifter. I'll check into that. Thanks. The boot is cracked and I can see the cement through it. Replacement coming as soon. Yes, it is a 30+ year old truck, and it's going to rattle and shake. I'm amazed that it doesn't sound worse than it does...I'm thinking the PO took good care of this ride. __________________ '72 Chevy K-20 Crate 350, SM465, 4.10's

02-21-2005, 02:30 PM	#5
72 Cheyenne K20 Registered User Join Date: Feb 2003 Location: Staunton, Virginia Posts: 554	I had the same prob with a 70 k20. PO use the wrong size bolt and no washers to hold the shifter. Replaced with correct bolt and washers and was tight as new. Scott



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.