|
|
|
01-20-2020, 05:25 PM
|
#1 |
|
Registered User
 Join Date: Jun 2018
Location: Sandy, Utah
Posts: 102
|
71 K20, Eaton H052
Hi folks, My 71 K20 has an open Eaton H052 rear Dif. I would like to convert it to a locker, either manual or automatic. I called Eaton and they said unofficialy I could use a Detroit Locker number 225S10. I need 30 spline axles for the Detroit. Has anybody done this conversion and know of an axle that would work? The axle shaft diameter is 1.5 in. I don't have a length. Any and all suggestions are welcome. Thanks, Jack
Last edited by Jack15T; 01-20-2020 at 05:28 PM. Reason: mis spelling |
|
|
|
01-20-2020, 06:07 PM
|
#2 |
|
Post Whore
 
Join Date: May 2015
Location: Alabama
Posts: 14,614
|
Re: 71 K20, Eaton H052
personally..id just get a locking 14b and swap it out...not sure on the widths though..but if possible itll be much cheaper than trying to do anything with the ho52
__________________
Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver |
|
|
|
|
01-20-2020, 06:18 PM
|
#3 |
|
Registered User
Join Date: Jun 2018
Location: Sandy, Utah
Posts: 102
|
Re: 71 K20, Eaton H052
Thanks Greg, I'll look into it.
|
|
|
|
|
01-20-2020, 07:29 PM
|
#4 |
|
Registered User
Join Date: May 2012
Location: horseheads,ny rust belt
Posts: 2,794
|
Re: 71 K20, Eaton H052
been told and read the detroit form a 14ff will swap inside the open carrier in place of the spider gears . then the 14ff shafts the correct length will swap over also . then you have a eaton ho with a locker .
__________________
77-k30lb BIG truck build . 87-k30lb budget beater build . 85-k30lb the plow machine build . 85-c10sb summer fun toy . ----------------------------- HOLLEY SNIPER efi = worst case of p.i.t.a i ever had . EDELBROCK pro flo 4 = best deal going so far . love my setup works great. |
|
|
|
|
01-20-2020, 08:09 PM
|
#5 |
|
Registered User
Join Date: Jun 2018
Location: Sandy, Utah
Posts: 102
|
Re: 71 K20, Eaton H052
That would be pretty nice. Thanks for the tip.
|
|
|
|
|
01-20-2020, 08:50 PM
|
#6 |
|
Registered User
Join Date: May 2012
Location: horseheads,ny rust belt
Posts: 2,794
|
Re: 71 K20, Eaton H052
i might be a bit off on info for the 52 .
but here is a MEGA thread on ho72 stuff https://www.pirate4x4.com/forum/chev...aton-h072.html
__________________
77-k30lb BIG truck build . 87-k30lb budget beater build . 85-k30lb the plow machine build . 85-c10sb summer fun toy . ----------------------------- HOLLEY SNIPER efi = worst case of p.i.t.a i ever had . EDELBROCK pro flo 4 = best deal going so far . love my setup works great. |
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
