Drive shaft length for 700r ? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Chvy2NV · 06-22-2013, 01:02 PM

Does anyone know the correct length I need to have my drive shaft cut down to inorder to run a 700r

Current setup

350 SB with TH350
Posted via Mobile Device

cdowns · 06-22-2013, 01:14 PM

to only pay havein the driveshaft done one time it is best for you to measure for yourself a few times to make sure of what you need

**1971 GMC SHORTY** · 06-22-2013, 02:04 PM

Reamber when doing Mesureing for new shaft Truck needs to be at ride hight!!!!

Hawssie · 06-22-2013, 02:16 PM

Definitely measure yourself. If its a 2 piece you would want to measure from the center of the 2 bolts that hold the center bearing to the tip of the output shaft at ride height. If 1 piece measure from the tip of the output shaft to the flats of the yoke. Some shops like to measure from the end of the tail shaft instead of the shaft itself minus the seal but either way would work as long as they know wht you measured, just make a note of how much shaft stick out you have out of the tail shaft just in case they want to know, mine was like 3/4 inch.

brad_man_72 · 06-22-2013, 10:54 PM

What they said. If 2 piece take them both pieces so they can ballance your shaft as an assembly.

I build driveshafts, good to see my advice is sinking in with the locals

Posted via Mobile Device

Chvy2NV · 06-23-2013, 01:35 AM

Thanks guys for the help and tips. It's a one piece shaft.
Posted via Mobile Device

tinsoldier · 06-23-2013, 09:10 AM

PIctures or diagram would help big time. As I am getting ready to put a 700r4 myself.

**DeadheadNM** · 06-23-2013, 09:14 AM

When I installed a 700r4 the engine was moved forward 1.75" so as to avoid cutting the drive shafts. This was in a 4x4 though. Can you just move the engine mounts?

Chvy2NV · 06-24-2013, 07:50 AM

Yes I can. My motor is sitting on the back mounts right now. More than likely. I'm going to measure once its all done just to avoid any issues. I was thinking of getting it cut before if it was a set or exact amount every time.

Quote:

Originally Posted by DeadheadNM

When I installed a 700r4 the engine was moved forward 1.75" so as to avoid cutting the drive shafts. This was in a 4x4 though. Can you just move the engine mounts?

Posted via Mobile Device

06-22-2013, 01:02 PM	#1
Chvy2NV Registered User Join Date: Apr 2012 Location: So. Florida Posts: 873	Drive shaft length for 700r ? Does anyone know the correct length I need to have my drive shaft cut down to inorder to run a 700r Current setup 350 SB with TH350 Posted via Mobile Device

06-22-2013, 01:14 PM	#2
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Drive shaft length for 700r ? to only pay havein the driveshaft done one time it is best for you to measure for yourself a few times to make sure of what you need __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

06-22-2013, 02:04 PM	#3
1971 GMC SHORTY Senior Member Join Date: Apr 2009 Location: SAN FERNANDO VALLE SOL CAL Posts: 1,064	Re: Drive shaft length for 700r ? Reamber when doing Mesureing for new shaft Truck needs to be at ride hight!!!! __________________ 1966 GMC K25 V6 351E Original Utility Truck 2000 C3500 Hot Rod Utility Truck 2003 ROAD KING 100th 124ci 6 Speed 145CI M/P Pro Street FXR 2002 FXDP 2007 2500HD DURAMAX. DD Studio Teamsters / Mechanic Retired GM Master Tech 20 Years Retired Ford Tech 15 Years

06-22-2013, 02:16 PM	#4
Hawssie Registered User Join Date: Mar 2013 Location: Clayton, Ca. Posts: 162	Re: Drive shaft length for 700r ? Definitely measure yourself. If its a 2 piece you would want to measure from the center of the 2 bolts that hold the center bearing to the tip of the output shaft at ride height. If 1 piece measure from the tip of the output shaft to the flats of the yoke. Some shops like to measure from the end of the tail shaft instead of the shaft itself minus the seal but either way would work as long as they know wht you measured, just make a note of how much shaft stick out you have out of the tail shaft just in case they want to know, mine was like 3/4 inch.

06-22-2013, 10:54 PM	#5
brad_man_72 the boat guy Join Date: Jul 2007 Location: springfield mo Posts: 2,339	Re: Drive shaft length for 700r ? What they said. If 2 piece take them both pieces so they can ballance your shaft as an assembly. I build driveshafts, good to see my advice is sinking in with the locals Posted via Mobile Device

06-23-2013, 01:35 AM	#6
Chvy2NV Registered User Join Date: Apr 2012 Location: So. Florida Posts: 873	Re: Drive shaft length for 700r ? Thanks guys for the help and tips. It's a one piece shaft. Posted via Mobile Device

06-23-2013, 09:10 AM	#7
tinsoldier Registered User Join Date: Mar 2013 Location: Peachtree Corners, GA Posts: 84	Re: Drive shaft length for 700r ? PIctures or diagram would help big time. As I am getting ready to put a 700r4 myself.

06-23-2013, 09:14 AM	#8
DeadheadNM Carpe manana Join Date: Dec 2010 Location: Eau Claire, WI Posts: 12,355	Re: Drive shaft length for 700r ? When I installed a 700r4 the engine was moved forward 1.75" so as to avoid cutting the drive shafts. This was in a 4x4 though. Can you just move the engine mounts? __________________ 1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308 Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.