![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Mar 2014
Location: Corona, CA
Posts: 26
|
First time swapping a motor, don't have much experience
Would anyone be able to help? I know this might be easy to most of you here, I'm not very savvy when it comes to mechanics, I can do the usual maintenance on any vehicle, but this is the first time I swap a motor, so my question is, how do I align the motor to the transmission, it's in but it won't close all the way, I'm doing this on my own, moving the engine hoist and the jack from the transmission to align it but it's not going in, the motor is a 305 off a 85 camaro, and the transmission is a th350 off the truck 72 c20, would that be the issue?
Posted via Mobile Device |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Oct 2005
Location: Overland Park, Ks.
Posts: 5,216
|
Re: First time swapping a motor, don't have much experience
You probably don't have the converter all the way back in the trans. There are about 3 steps going in. You have to rotate the converter holding the weight up till it drops back. The engine should bolt right up to that trans. If you get the angles the same & the dowels go into the holes it will fit up. The converter will be about 1/4 in back from the flywheel. After you get the engine bolted to the trans. You can drop it down on the mounts. Pull the converter forward to the flywheel & bolt it up.
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Mar 2014
Location: Corona, CA
Posts: 26
|
I'm trying to upload an image of how far it's in there it's pretty much there but won't go in anymore than that
Posted via Mobile Device |
![]() |
![]() |
![]() |
#4 |
Senior Member
![]() Join Date: Jun 2009
Location: Belews Creek , NC
Posts: 4,220
|
Re: First time swapping a motor, don't have much experience
It appears you are probably close as you might get, put your bolts in the bell housing and it should draw together, just don't force it. If it feels real hard to run the bolts in stop. Also like Wrenchbender said look up from the bottom and make sure your torque converter isn't bottomed out on the flywheel
__________________
Larry It is easily overlooked that what is now called vintage was once brand new. "Project 68" paypal.me/ldgrant |
![]() |
![]() |
![]() |
#5 | ||
"I ain't nobody, dork."
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,936
|
Re: First time swapping a motor, don't have much experience
Dowel pin in the transmission isn't lined up with the engine. The tranny and engine MUST mate up flush with each other.
Gary
__________________
'cuz chicks dig scars... My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread. The Rebuild of Creeping Death after the wreck Quote:
Quote:
|
||
![]() |
![]() |
![]() |
#6 | |
Registered User
Join Date: Mar 2014
Location: Corona, CA
Posts: 26
|
Quote:
Posted via Mobile Device |
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Mar 2014
Location: Corona, CA
Posts: 26
|
Re: First time swapping a motor, don't have much experience
Posted via Mobile Device
|
![]() |
![]() |
![]() |
#8 |
Account Suspended
![]() Join Date: Jul 2016
Location: Tacoma, WA
Posts: 6,873
|
Re: First time swapping a motor, don't have much experience
Turn the torque converter by hand and while turning push it in. It should not be touching the flywheel at all even when the transmission is fully bolted to the engine
|
![]() |
![]() |
![]() |
#9 |
Account Suspended
![]() Join Date: Jul 2016
Location: Tacoma, WA
Posts: 6,873
|
Re: First time swapping a motor, don't have much experience
You have it close so put a few bolts in to keep the alignment and check the converter clearance.
|
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Mar 2014
Location: Corona, CA
Posts: 26
|
|
![]() |
![]() |
![]() |
#11 | ||
"I ain't nobody, dork."
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,936
|
Re: First time swapping a motor, don't have much experience
Great!
I realized this morning I said the dowels in the transmission, but I meant the dowels in the engine to line up the transmission. ![]() Good job! Gary
__________________
'cuz chicks dig scars... My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread. The Rebuild of Creeping Death after the wreck Quote:
Quote:
|
||
![]() |
![]() |
![]() |
Bookmarks |
|
|