![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
People know me
Join Date: Jun 2007
Location: Hermiston, oregon
Posts: 840
|
door glass channel glue
So I am getting ready to pull my Blazer off the back burner and put it back together so I can enjoy some snow wheeling this winter.
I got a little carried away with the body work and panel replacement and welded up the mirror holes in the doors, Like an idiot I had the windows rolled down in the doors and didnt think twice about it. Well I got some seriously slag burnt windows now. I just got some replacement windows from my co worker, but they dont have the metal channels attached to them, I will have to re-use my old ones. I have had bad luck with one in the past always comming loose from the channel. How do I swap them, is there a glue that would work better?
__________________
1972 k/5 blazer CST 4X4 Crate 350, th350/205, dana44with trac-loc/14 bolt with detroit locker, 4 wheel discs 4.56s, 8" suspension lift using 73-87springs, 1" zerorate custom front crossmember, HAD CV drivelines and driveshaft e-brake, full cage, PRP seats, Full autometer gauges, 38x14.5x16 Toyo M/Ts, 16x10 Polished aluminum rockcrusher wheels 1967 longbox 4x4, Strong 400/400/208, 44/12bolt 4.10s, 6" lift, 35" Toyo M/Ts on corvette rally wheels |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Re: door glass channel glue
Most glass shops have the rubber strip that they can use to install the window in the channel. If the old rubber strip is in good condition then I use 3M Weatherstrip Adhesive to glue the window in. I have done several this way over the last 20 years and have not had a failure.
Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC |
![]() |
![]() |
![]() |
#3 |
Carpe manana
![]() ![]() Join Date: Dec 2010
Location: Eau Claire, WI
Posts: 12,399
|
Re: door glass channel glue
Auto glass shops use rubber glass setting "tape" and it comes in varied thicknesses. I just brought in a vent window and had it set for $7.
__________________
1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308 ![]() |
![]() |
![]() |
![]() |
#4 | |
Registered User
Join Date: Feb 2000
Location: Center City, MN, USA
Posts: 3,254
|
Re: door glass channel glue
Quote:
A long time ago before this forum was really where it is today I ordered a piece of the "tape" from LMC. My dad was over one day and I asked him how I set the glass in the channel. He asked for a hunk of 2x4. He proceeded to take the glass, channel, rubber, and 2x4 out on to my lawn and proceeded to WHACK the channel on the bottom of the glass with the rubber in between. It has been a long time but I think he had me mix up some soapy water to act as a lubricant which of course later disappeared when it was dry.
__________________
'70 cab, '71 chassis, 383, TH350, NP205. '71 Malibu convertible '72 Malibu hard top Center City, MN |
|
![]() |
![]() |
![]() |
Bookmarks |
|
|