67 C10 step side exhaust ideas - The 1947 - Present Chevrolet & GMC Truck Message Board Network

scoobiedoo01 · 11-06-2018, 02:32 PM

I'm in the middle of finishing up my 67 C10 step side and am trying to figure the best route to plumb the exhaust. I'm running 3" pipe all the way back and thinking of running the exhaust through the rear quarter panel either just before or after the tire. Do any of you guys have any pics of yours that I could see for ideas?

benw88 · 11-07-2018, 03:25 PM

Quote:

Originally Posted by scoobiedoo01

I'm in the middle of finishing up my 67 C10 step side and am trying to figure the best route to plumb the exhaust. I'm running 3" pipe all the way back and thinking of running the exhaust through the rear quarter panel either just before or after the tire. Do any of you guys have any pics of yours that I could see for ideas?

Those are the best pics I have at the moment. I have 2.5” pipes that kick out at roughly 30 degrees, then I have a SS exhaust tip that is cut off at 45degrees so it’s flush with the bottom of the step on each side of the truck. The tip is 3”
Posted via Mobile Device

mr.precision · 11-07-2018, 04:00 PM

Original 1967 stepper. Dual exhaust is at least 20 years old. Hope this helps.

68Stepbed · 11-08-2018, 09:58 AM

Take it out the rear!

**michael bustamante** · 11-08-2018, 12:38 PM

68stepbed. I like where you dumped em I might do that too!
67 GMC

scoobiedoo01 · 11-08-2018, 03:36 PM

68Stepbed. I like this set up. What size pipe are you using? I want to run 3" all the way back and right behind the tires would be just right if 3" will fit okay.

Mike C · 11-08-2018, 08:01 PM

IMO, you will be much happier all the way around if you run a 2 1/2" system rather than a 3". Cost is WAY higher for the 3" and much more difficult to route. If you are making 600hp and need it then I guess... But I'm planning a 2 1/2" system behind my 450hp 427.

I too am a "run it out the back" guy. On my leaf spring truck I cut holes in the crossmember where the trailing arms would bolt and I welded in 4" pipe reinforcements and will tuck and run my exhaust as high as possible.

**HO455** · 11-09-2018, 12:01 AM

I agree with Mike C about sizing. I ran mine out Zoomie style on my Burban to keep the exhaust out of the interior. My rear hatches barely keep water out let alone fumes.

Sorry about the poor photos

68Stepbed · 11-09-2018, 09:25 AM

Quote:

Originally Posted by scoobiedoo01

68Stepbed. I like this set up. What size pipe are you using? I want to run 3" all the way back and right behind the tires would be just right if 3" will fit okay.

Mine is 2.5" pipe. I have a 530hp LS1 and these breathe very well. As Mike C mentioned, 3" is overkill unless you're making above 600hp. That said, 3" is difficult to route to the back, but it's possible for someone that knows what they're doing. My TCI rear suspension created an even more complicated routing scenario than stock suspension, so the stainless mandrel bent setup was the only way to go.

68Stepbed · 11-09-2018, 09:31 AM

The best part is the exhaust is tucked and isn't seen at all.

scoobiedoo01 · 11-09-2018, 11:26 AM

68Stepbed. That is exactly what I want. Nothing hanging down at all. Nice looking truck!

Mike C · 11-09-2018, 09:19 PM

I assume his TCI suspension has clearances for the pipes through the center crossmember. I know the drop-members are made that way. Here is my mods to my truck. Leaf springs make it easier...

And these made me chuckle. The pieces I cut out pretty much were Pacmen.

11-06-2018, 02:32 PM	#1
scoobiedoo01 Registered User Join Date: May 2018 Location: Waterloo Posts: 13	67 C10 step side exhaust ideas I'm in the middle of finishing up my 67 C10 step side and am trying to figure the best route to plumb the exhaust. I'm running 3" pipe all the way back and thinking of running the exhaust through the rear quarter panel either just before or after the tire. Do any of you guys have any pics of yours that I could see for ideas?

11-07-2018, 04:00 PM	#3
mr.precision Registered User Join Date: Feb 2018 Location: Fountain Hills, AZ Posts: 161	Re: 67 C10 step side exhaust ideas Original 1967 stepper. Dual exhaust is at least 20 years old. Hope this helps. Attached Images

11-08-2018, 09:58 AM	#4
68Stepbed Registered User Join Date: Mar 2005 Location: 10-Uh-See Posts: 5,609	Re: 67 C10 step side exhaust ideas Take it out the rear! __________________ Matt 68 C10 stepside, LS1/700R4, TCI Engineering suspension system

11-08-2018, 12:38 PM	#5
michael bustamante Senior Member Join Date: Sep 2007 Location: Albuquerque NM Posts: 7,858	Re: 67 C10 step side exhaust ideas 68stepbed. I like where you dumped em I might do that too! 67 GMC __________________ 1967custom

11-08-2018, 03:36 PM	#6
scoobiedoo01 Registered User Join Date: May 2018 Location: Waterloo Posts: 13	Re: 67 C10 step side exhaust ideas 68Stepbed. I like this set up. What size pipe are you using? I want to run 3" all the way back and right behind the tires would be just right if 3" will fit okay.

11-08-2018, 08:01 PM	#7
Mike C Registered User Join Date: Dec 1999 Location: Austin, TX, USA Posts: 7,723	Re: 67 C10 step side exhaust ideas IMO, you will be much happier all the way around if you run a 2 1/2" system rather than a 3". Cost is WAY higher for the 3" and much more difficult to route. If you are making 600hp and need it then I guess... But I'm planning a 2 1/2" system behind my 450hp 427. I too am a "run it out the back" guy. On my leaf spring truck I cut holes in the crossmember where the trailing arms would bolt and I welded in 4" pipe reinforcements and will tuck and run my exhaust as high as possible. __________________ 44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax

11-09-2018, 12:01 AM	#8
HO455 Post Whore Join Date: Feb 2016 Location: Portland Oregon Posts: 11,276	Re: 67 C10 step side exhaust ideas I agree with Mike C about sizing. I ran mine out Zoomie style on my Burban to keep the exhaust out of the interior. My rear hatches barely keep water out let alone fumes. Sorry about the poor photos Attached Images __________________ Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. RIP Bob Parks. 1967 Burban (the WMB),1988 S10 Blazer (the Stink10 II),1969 GTO (the Goat), 1970 Javelin, 1952 F2 Ford OHC six 4X4, 29 Model A, 72 Firebird (the DBP Bird). 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377

11-09-2018, 09:31 AM	#10
68Stepbed Registered User Join Date: Mar 2005 Location: 10-Uh-See Posts: 5,609	Re: 67 C10 step side exhaust ideas The best part is the exhaust is tucked and isn't seen at all. __________________ Matt 68 C10 stepside, LS1/700R4, TCI Engineering suspension system

11-09-2018, 11:26 AM	#11
scoobiedoo01 Registered User Join Date: May 2018 Location: Waterloo Posts: 13	Re: 67 C10 step side exhaust ideas 68Stepbed. That is exactly what I want. Nothing hanging down at all. Nice looking truck!

11-09-2018, 09:19 PM	#12
Mike C Registered User Join Date: Dec 1999 Location: Austin, TX, USA Posts: 7,723	Re: 67 C10 step side exhaust ideas I assume his TCI suspension has clearances for the pipes through the center crossmember. I know the drop-members are made that way. Here is my mods to my truck. Leaf springs make it easier... And these made me chuckle. The pieces I cut out pretty much were Pacmen. __________________ 44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.