cable vs. rod for carb - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dan42 · 11-03-2007, 10:50 AM

Can anyone tell if there is a compelling reason to change from the stock rod configuration for your throttle linkage to cable? Is the response different? Are there any serious safety issues? Putter has a good thread for converting to cable, but if there isn't much difference, then I'll leave it stock. Is there another method of converting besides Putter's that people have tried? Any info on this would be greatly appreciated.

Jim_PA · 11-03-2007, 11:19 AM

If you break an engine mount, the rod can cause the throttle to stick wide open when the engine lifts. That won't happen with a cable.

I'm either going to add some kind of safety cable around the frame to the engine, or go to a cable some day.

70short · 11-03-2007, 11:38 AM

I was considering converting to the LOKAR firewall mounted Throttle pedal with cable versus the factory floor mount style I currently have. However this is further down on my list of priority's right now.

Gary

HeavyD · 11-03-2007, 12:01 PM

Many of the trucks I owned had rod linkage and never gave me any trouble. I personally wouldn't change it.

Longhorn Man · 11-03-2007, 04:34 PM

in 71 they chainged becouse of the number of motormounts that were breaking. If you hit the throttle and pop the drivers side mount, the engine will lean over and lock the throttle or even open the throttle more. This was a big enough problem that there was a recall, and we all know how much the bean counters hate spending money on recalls.
With that being said, I wouldn't bother personally.

acl · 11-03-2007, 04:38 PM

had bought lokar but looking at my application i would of only used 6 inches of it so returned it and went back with rod.
Gary

70short · 11-04-2007, 02:29 AM

they have alternatives to LOKAR that are less expensive.

Gary

Spray-Bomb · 11-04-2007, 10:17 AM

I can't remember if I went off of putters plans or who's, but somebody on here does have a good build on converting to cable

If you look in my build thread you can see what I did, I did it just to have swing pedal & be different

But I can't tell that it drives any different than a "rod" style throttle

Ackattack · 11-04-2007, 10:49 AM

I say skip the cable and go with a wire. It's a little more of an upgrade though (5.3L DBW

)

11-03-2007, 10:50 AM	#1
dan42 Registered User Join Date: Feb 2007 Location: Cali Central Coast Posts: 5,191	cable vs. rod for carb Can anyone tell if there is a compelling reason to change from the stock rod configuration for your throttle linkage to cable? Is the response different? Are there any serious safety issues? Putter has a good thread for converting to cable, but if there isn't much difference, then I'll leave it stock. Is there another method of converting besides Putter's that people have tried? Any info on this would be greatly appreciated. __________________ '67 SWB Fleetside ZZ4/350/Tremec 5-speed/4link/Scott's IFS - and fun as heck! SOLD Click here to support the board Philippians 4: 6-7

11-03-2007, 11:19 AM	#2
Jim_PA Registered User Join Date: May 2005 Location: PA Posts: 2,696	Re: cable vs. rod for carb If you break an engine mount, the rod can cause the throttle to stick wide open when the engine lifts. That won't happen with a cable. I'm either going to add some kind of safety cable around the frame to the engine, or go to a cable some day.

11-03-2007, 11:38 AM	#3
70short Registered User Join Date: Sep 2003 Location: Boise ID Posts: 609	Re: cable vs. rod for carb I was considering converting to the LOKAR firewall mounted Throttle pedal with cable versus the factory floor mount style I currently have. However this is further down on my list of priority's right now. Gary __________________ "72" Red CORVETTE 4-speed 350 "70" Chevy Short Bed early stages of resto. Edel 600 cfm carb Weiand Stealth Intake HEI shorty Headers 4/2 Drop 295 50R 15 TOYO on 10 inch wide corvette rally rims at all 4 corners. "CHEVY RULES"

11-03-2007, 12:01 PM	#4
HeavyD Senior Member Join Date: Sep 2004 Location: Wakaw, Sask, Canada Posts: 3,180	Re: cable vs. rod for carb Many of the trucks I owned had rod linkage and never gave me any trouble. I personally wouldn't change it. __________________ "You can take the man out of PA, but you can't take PA out of the man"

11-03-2007, 04:34 PM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Re: cable vs. rod for carb in 71 they chainged becouse of the number of motormounts that were breaking. If you hit the throttle and pop the drivers side mount, the engine will lean over and lock the throttle or even open the throttle more. This was a big enough problem that there was a recall, and we all know how much the bean counters hate spending money on recalls. With that being said, I wouldn't bother personally.

11-03-2007, 04:38 PM	#6
acl Registered User Join Date: May 2007 Location: Emporia, kansas Posts: 300	Re: cable vs. rod for carb had bought lokar but looking at my application i would of only used 6 inches of it so returned it and went back with rod. Gary

11-04-2007, 02:29 AM	#7
70short Registered User Join Date: Sep 2003 Location: Boise ID Posts: 609	Re: cable vs. rod for carb they have alternatives to LOKAR that are less expensive. Gary __________________ "72" Red CORVETTE 4-speed 350 "70" Chevy Short Bed early stages of resto. Edel 600 cfm carb Weiand Stealth Intake HEI shorty Headers 4/2 Drop 295 50R 15 TOYO on 10 inch wide corvette rally rims at all 4 corners. "CHEVY RULES"

11-04-2007, 10:17 AM	#8
Spray-Bomb Texas Big Wig Join Date: Jan 2007 Location: Mineola, Texas Posts: 5,620	Re: cable vs. rod for carb I can't remember if I went off of putters plans or who's, but somebody on here does have a good build on converting to cable If you look in my build thread you can see what I did, I did it just to have swing pedal & be different But I can't tell that it drives any different than a "rod" style throttle __________________ Just not low enough... ----------------------------- Sinister Killer

11-04-2007, 10:49 AM	#9
Ackattack Senior Member Join Date: Aug 2002 Location: Valley Center KS Posts: 3,525	Re: cable vs. rod for carb I say skip the cable and go with a wire. It's a little more of an upgrade though (5.3L DBW ) __________________ Project Bruiser: 68 Pro-Touring C-10 5.3L / 4L60E Project Ironhide: 97 GMC Crew Cab 4x4 Cummins SOLD: '69 GMC 1/2T SWB TBI'd: Project No Buck Assembly Manual Index Sign up Thread!!! Factory Service Manual Index



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.