Painless wiring - The 1947 - Present Chevrolet & GMC Truck Message Board Network

cwgreen1971 · 12-19-2010, 04:07 PM

I am getting ready to head out to the garage and start wiring my truck. I bought the Painless #10206 kit which they say is pretty easy. It is all new to me. Does anyone have any tips or suggestions that may be helpful. I'm just doing the basic... lights/signals, ignition, dome light, horn, dash. I want to hide as much as possible...thanks

haysonj · 12-19-2010, 05:39 PM

Quote:

Originally Posted by cwgreen1971

I am getting ready to head out to the garage and start wiring my truck. I bought the Painless #10206 kit which they say is pretty easy. It is all new to me. Does anyone have any tips or suggestions that may be helpful. I'm just doing the basic... lights/signals, ignition, dome light, horn, dash. I want to hide as much as possible...thanks

Just take your time and do one section at a time. I thought the instructions were pretty good. Here's mine when I first started.

Transformula · 12-19-2010, 07:28 PM

Yeah what he said!
Work from the fuse panel, working in the main bunch and as you branch off each circuit, lay them out roughly where they go, and fine tune the layout as you go. Most importantly, DO NOT CUT OR TERMINATE ANY WIRES UNTIL THE HARNESS AND BRANCHES ARE LAYED OUT EXACTLY WHERE THEY NEED TO GO!! They provide lots of zip ties, but I wind up using way more. It just makes it look neater. I also like to add chinese finger-type loom covering, P-clamps, and now is the time to add any wires or circuits you may want or need to make a completely custom setup!
I've installed 3 of the Painless harnesses, and the more time you spend, the better the result.
Get some heat shrink tubing and seal up all connections for a pro-look!

**Tom Vogel** · 12-20-2010, 09:47 AM

Quote:

Originally Posted by Transformula

Yeah what he said!
Work from the fuse panel, working in the main bunch and as you branch off each circuit, lay them out roughly where they go, and fine tune the layout as you go. Most importantly, DO NOT CUT OR TERMINATE ANY WIRES UNTIL THE HARNESS AND BRANCHES ARE LAYED OUT EXACTLY WHERE THEY NEED TO GO!! They provide lots of zip ties, but I wind up using way more. It just makes it look neater. I also like to add chinese finger-type loom covering, P-clamps, and now is the time to add any wires or circuits you may want or need to make a completely custom setup!
I've installed 3 of the Painless harnesses, and the more time you spend, the better the result.
Get some heat shrink tubing and seal up all connections for a pro-look!

Great Advice!

1970 CST STEP · 12-21-2010, 10:38 PM

Quote:

Originally Posted by haysonj

Just take your time and do one section at a time. I thought the instructions were pretty good. Here's mine when I first started.

+1 TAKE YOUR TIME !!! It will pay off in the long run.

tubbedII · 12-20-2010, 12:43 PM

You've already got some great advise. One thing I wish I did (and still am hoping to do) is get the black braided loom to wrap the wires. I used black tape and not only was it a PITA to do, it doesn't look very good where it is visible.

cwgreen1971 · 12-20-2010, 04:51 PM

Quote:

Originally Posted by tubbedII

You've already got some great advise. One thing I wish I did (and still am hoping to do) is get the black braided loom to wrap the wires. I used black tape and not only was it a PITA to do, it doesn't look very good where it is visible.

The "powerbraid" kit Painless sells is $220, that is over half of what I paid for the wiring kit!!!!! Where else can you get that stuff?

haysonj · 12-20-2010, 06:01 PM

Quote:

Originally Posted by cwgreen1971

The "powerbraid" kit Painless sells is $220, that is over half of what I paid for the wiring kit!!!!! Where else can you get that stuff?

I bought mine from Jegs and only bought what I needed instead of a kit. http://www.jegs.com/webapp/wcs/store...94962727&Nty=0

Stubbs67 · 12-21-2010, 10:50 PM

Quote:

Originally Posted by cwgreen1971

The "powerbraid" kit Painless sells is $220, that is over half of what I paid for the wiring kit!!!!! Where else can you get that stuff?

Fry's Electronics sells it by the roll. Fairly cheap.

tubbedII · 12-20-2010, 07:13 PM

Quote:

Originally Posted by cwgreen1971

The "powerbraid" kit Painless sells is $220, that is over half of what I paid for the wiring kit!!!!! Where else can you get that stuff?

Exactly the reason I didn't do it to begin with...

Quote:

Originally Posted by haysonj

I bought mine from Jegs and only bought what I needed instead of a kit. http://www.jegs.com/webapp/wcs/store...94962727&Nty=0

Never looked into it any deeper after seeing the kit price! Thanks for the info and link!

cwgreen1971~ The only places I was planning on running this loom is in the engine bay. Everything off the firewall's harness, so this is actually affordable now (at least in my case).

FRENCHBLUE72 · 12-21-2010, 11:17 PM

I did my blazer with a painless kit and it took about 4 days really taking my time..

12-19-2010, 07:28 PM	#3
Transformula Registered User Join Date: Nov 2010 Location: Las Vegas, Nevada Posts: 160	Re: Painless wiring Yeah what he said! Work from the fuse panel, working in the main bunch and as you branch off each circuit, lay them out roughly where they go, and fine tune the layout as you go. Most importantly, DO NOT CUT OR TERMINATE ANY WIRES UNTIL THE HARNESS AND BRANCHES ARE LAYED OUT EXACTLY WHERE THEY NEED TO GO!! They provide lots of zip ties, but I wind up using way more. It just makes it look neater. I also like to add chinese finger-type loom covering, P-clamps, and now is the time to add any wires or circuits you may want or need to make a completely custom setup! I've installed 3 of the Painless harnesses, and the more time you spend, the better the result. Get some heat shrink tubing and seal up all connections for a pro-look! __________________ T.Y.N Custom Works..... Because "Stock" Sucks! 1971 K 10 GMC Long Bed 1977 Formula T/A Frame off Resto-Mod 1995 FXDL Harley Low Rider 1985 C10 ShortWide 91 Burb front.

12-20-2010, 12:43 PM	#6
tubbedII needs more $$$ Join Date: Mar 2004 Location: Sacramento Posts: 1,936	Re: Painless wiring You've already got some great advise. One thing I wish I did (and still am hoping to do) is get the black braided loom to wrap the wires. I used black tape and not only was it a PITA to do, it doesn't look very good where it is visible. __________________ 1970 2wd Blazer

12-21-2010, 11:17 PM	#11
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,608	Re: Painless wiring I did my blazer with a painless kit and it took about 4 days really taking my time.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

12-19-2010, 04:07 PM	#1
cwgreen1971 cwgreen1971 Join Date: Aug 2008 Location: Battle Creek MI Posts: 185	Painless wiring I am getting ready to head out to the garage and start wiring my truck. I bought the Painless #10206 kit which they say is pretty easy. It is all new to me. Does anyone have any tips or suggestions that may be helpful. I'm just doing the basic... lights/signals, ignition, dome light, horn, dash. I want to hide as much as possible...thanks



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.