My last hoorah...1972 K20 Cheyenne Super frame off

[52napco]

I've bought quite a few trucks over the years looking for that elusive "right one" and just never found it...came close several times, have a few hoarded back and sold a couple I probably should have kept.
Anyway I came to grips that I was just going to have to restore what I wanted..wishlist was short but hard to find in a 48 year old truck.
1- Cheyenne Super
2-Original drivetrain
3-Legit truck with original spid
4-automatic trans
5-factory a/c
So the last one I bought in Lake Havasu AZ is officially the one. Doing a "driver" restoration
to still enjoy it but look good.. Unfortunately it wasn't as described but still a legit overall good truck.needs cab corners, inner and outer rockers and all 4 cab supports, so we'll do a 1 piece floor.. ds bedside is dented up to the point that I'm just replacing it with a super nice one I had and replacing front bed panel due to a few dents.
enjoy the pics, more to come..

[52napco]

And how it looks today

[52napco]

More pics

[DeadheadNM]

Nice survivor. Please post any detail pics you can for future restorations.

[57taskforce]

I’m in for this one! That’s an excellent starting point and after seeing some of your other work I’m confident this one will come out great!

[52napco]

Floor out ready for new 1 pc floor..outer rockers were decent just all 4 cab supports shot and inner.rockers bad..Strange how the trucks rust in these places...toe kicks were perfect.

[52napco]

Floor back in..going to cut the hump area out
AMD sent the low hump instead but no big deal
Got frame stripped down for blasting and engine off to
the machine shop

[weim55]

Originally Posted by 52napco

Floor out ready for new 1 pc floor..outer rockers were decent just all 4 cab supports shot and inner.rockers bad..Strange how the trucks rust in these places...toe kicks were perfect.

Good OUTER rockers and everything inboard rusted out ??!! I’ve been around hundreds of these trucks and I can’t say I’ve ever seen that! Must be an Arizona thing........

Steve weim55 Colorado

[52napco]

Probably could have saved the floor but all the cab supports and inner rockers were toast it just makes such a cleaner job with the one piece floorm

[DeadheadNM]

Originally Posted by weim55

Good OUTER rockers and everything inboard rusted out ??!! I’ve been around hundreds of these trucks and I can’t say I’ve ever seen that! Must be an Arizona thing........

Steve weim55 Colorado

I had a truck where the rust was confined to the inner rockers. Think wet shoes and boots with a rubber floor mat that trapped the moisture near the kickpanel and inner rocker.

[davischevy]

I'm watching.

[57taskforce]

Originally Posted by weim55

Good OUTER rockers and everything inboard rusted out ??!! I’ve been around hundreds of these trucks and I can’t say I’ve ever seen that! Must be an Arizona thing........

Steve weim55 Colorado

My K10 is like that too. The inners are rusted at the top where they spot weld to the outers. I believe Pete is right on this one, that’s about all I could figure too. The rust is from the inside out. Nice progress on the tear down!

[Chevyland]

Originally Posted by 52napco

Floor out ready for new 1 pc floor..outer rockers were decent just all 4 cab supports shot and inner.rockers bad..Strange how the trucks rust in these places...toe kicks were perfect.

Originally Posted by weim55

Good OUTER rockers and everything inboard rusted out ??!! I’ve been around hundreds of these trucks and I can’t say I’ve ever seen that! Must be an Arizona thing........

Steve weim55 Colorado

I’ve had a few trucks from
Utah Montana
Look good on the outside
But
Underneath, cab supports were rusted out
I figured it was salt on roads
But otherwise, dry climates?

[Chevyland]

I’m in
Nice find

[Ol Blue K20]

I'm in to watch.....

[jimbosprint]

Should be a nice build. I look forward to watching the progress.

[chewychevy67]

I want to see how that floor is going to fit with the rockers attached. I kind of have the same problem so I'll be watching your photos of the replacement

[52napco]

Floor fit like a glove...the AMD stuff seems to work great but who knows if its not stamped in one place and marketed under various names ??? Going a different route and taking fenders, doors, hood, radiator support, and all small parts including air filter, engine brackets etc for dipping Monday...will post pics of that next week

[davischevy]

So you have somebody that still strips parts chemically? Our chemical stripper has been gone for years.

[52napco]

Originally Posted by davischevy

So you have somebody that still strips parts chemically? Our chemical stripper has been gone for years.

Yes we do in Anderson SC

[52napco]

Of the rain holds off this week my buddy will get the frame and axles blasted

[DeadheadNM]

Is the gear ratio tag on the front axle? If so, what location? Thanks. Looks solid.

[52napco]

Originally Posted by DeadheadNM

Is the gear ratio tag on the front axle? If so, what location? Thanks. Looks solid.

Don't think the cover has been off

[Michael D]

52napco, just curious, did your seller in havasu live on McCulloch?
I always see a lot of 67-72 trucks when I drive past his place.

[52napco]

Originally Posted by Michael D

52napco, just curious, did your seller in havasu live on McCulloch?
I always see a lot of 67-72 trucks when I drive past his place.

Don't think so...he worked at the fire dept and did a little grading
On his days off. Dont think he was a truck guy