u-bolt size - The 1947 - Present Chevrolet & GMC Truck Message Board Network

walls · 09-16-2011, 08:15 PM

I'm currently lowering my suburban a few inches and also installing a shock relocater kit from cpp. I cannot get the nuts off of the U-bolts to install the bottom shock mount. I've tried heat and put a pipe on my ratchet and still nothing. I think I'm going to have to cut them off.

Anyway, my question is will 1/2" U-bolts be sufficient?

The stock U-bolts are 3/4" diameter. The only U-bolts that I can buy locally are 1/2". I've checked all the auto parts stores and I can't find a suspension shop locally. I can order a set from Napa (5/8" and will still take 3 days) or I can order a set online.

Any opinions. Thanks

SCOTI · 09-16-2011, 08:25 PM

They need to be the larger (3/4"?) diameter.

The typical local auto parts store 1/2" units are usually for leaf applications. They slip over the housing tube 90° to the tube so they only need 3"ID. The truck arm arrangement requires more ID clearance because they're not @ 90°.

These are available from more than one board supporting vendor as well.

BMERDOC · 09-16-2011, 08:38 PM

I bought mine at www.atssprings.com Not trying to sound like thier spokesman but they had what I needed at the best price I could find on the internet.

09-16-2011, 08:15 PM	#1
walls Registered User Join Date: Aug 2011 Location: Green Lane PA Posts: 55	u-bolt size I'm currently lowering my suburban a few inches and also installing a shock relocater kit from cpp. I cannot get the nuts off of the U-bolts to install the bottom shock mount. I've tried heat and put a pipe on my ratchet and still nothing. I think I'm going to have to cut them off. Anyway, my question is will 1/2" U-bolts be sufficient? The stock U-bolts are 3/4" diameter. The only U-bolts that I can buy locally are 1/2". I've checked all the auto parts stores and I can't find a suspension shop locally. I can order a set from Napa (5/8" and will still take 3 days) or I can order a set online. Any opinions. Thanks

09-16-2011, 08:25 PM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,031	Re: u-bolt size They need to be the larger (3/4"?) diameter. The typical local auto parts store 1/2" units are usually for leaf applications. They slip over the housing tube 90° to the tube so they only need 3"ID. The truck arm arrangement requires more ID clearance because they're not @ 90°. These are available from more than one board supporting vendor as well. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

09-16-2011, 08:38 PM	#3
BMERDOC Registered User Join Date: Jun 2011 Location: Richmond,Va Posts: 2,934	Re: u-bolt size I bought mine at www.atssprings.com Not trying to sound like thier spokesman but they had what I needed at the best price I could find on the internet. __________________ Nick Carter 1967 C10 Short bed Fleetside Project Cheap Thrills! 2WD C10 Modern/Performance Alignments Easiest Alignment Ever!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.