![]() |
|
![]() |
#1 |
Registered User
Join Date: Mar 2007
Location: Oregon
Posts: 109
|
![]()
Hi all,
I am replacing the clutch on my K20, and I would really like to clean off the tranny and transfer case before putting them back in. They are covered with the thickest, nastiest grease and crud probably dating back to 1972. The standard engine degreaser and a garden hose is just not cutting it. Any tips? Thanks, Colby. |
![]() |
![]() |
![]() |
#2 |
Under Construction
Join Date: Oct 2007
Location: Midlothian,TX (DFW)
Posts: 4,555
|
Re: Degreasing
some oven cleaner from the dollar store.... buy a few cans spray it down heavily, let it set in the sun for a few hours then hose it off with high pressure.... of course scrapping with a putty knife first will help if as thick as you state.
__________________
Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470 Last edited by my67chevytruck; 03-11-2010 at 01:33 PM. |
![]() |
![]() |
![]() |
#3 |
Restoring it $200 at a time...
Join Date: Aug 2008
Location: NE Kansas
Posts: 886
|
Re: Degreasing
Take a couple of hours with a plastic putty knife and a wire brush before the liquids come out. Make sure you're on a tarp or gravel though; that crap is like glue on a concrete surface.
Once I had the trans pretty well scraped, I did 409 and a toothbrush to get it ready for paint.
__________________
Charter member of the 'Put the dimmer switch back on the damn floor where it belongs' Society '68 5.3L-4 speed LWB C20; grandpa bought it for the farm in '71. Now LS 5.3, rather than 327. DD '09 Pilot Weekender '65 Skylark 300-4V-4 speed Wife's '07 Lexus ES350; 117 actuator motors and I can't see the engine. Son's '04 F250 SuperCab 6.0 |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Nov 2009
Location: Mesa, AZ
Posts: 226
|
Re: Degreasing
x2 with oven cleaner and a pressure washer.
let the oven cleaner sit on there a bit to penetrate. Simple green works good to finish up with. |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Dec 2009
Location: DFW, TX
Posts: 764
|
Re: Degreasing
I've had much better results with easy off extra strength over cleaner than the cheap off brand stuff. Might buy one can of the good stuff and test it for yourself.
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jul 2006
Location: Columbia, SC
Posts: 410
|
Re: Degreasing
maybe a pressure washer
__________________
1968 Chevy C10 swb fleetside ![]() 2005 Chevy Silverado crew cab (SS) 1977 Goldwing cafe racer 1977 Chevy nova (first car/ first love) ![]() |
![]() |
![]() |
![]() |
#7 |
One foot in front of the other
![]() Join Date: Aug 2008
Location: Parrottsville, TN
Posts: 5,440
|
Re: Degreasing
Hot water pressure washer is the ticket.
|
![]() |
![]() |
![]() |
#8 |
Registered User
![]() Join Date: Sep 2000
Location: C-WY
Posts: 236
|
Re: Degreasing
I took mine to my favoriate car wash. It was nasty getting up under there and sprayen it but it cleaned it up purty good. Go to a good car wash because some car washes do not have enough presure to p.
__________________
69 stepside, 1/2ton, 4X4, 350/350/205 |
![]() |
![]() |
![]() |
#9 |
69 Fleetside
![]() Join Date: Mar 2009
Location: Lake Stevens, WA
Posts: 333
|
Re: Degreasing
be careful with over cleaner on aluminum...it started to eat at the finish on my starter really quick...but did an amazing job of degreasing and after a couple treatments while leaving it on only 10 minutes at a time and a green scouring pad, my engine bay was super shiney!!
|
![]() |
![]() |
![]() |
#10 |
2WD Jimmy
![]() Join Date: Mar 2005
Location: Davis County, Utah
Posts: 2,564
|
Re: Degreasing
Does oven cleaner work better than Gunk?
|
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Dec 2009
Location: DFW, TX
Posts: 764
|
Re: Degreasing
The brand name over cleaner worked better than gunk for me. The off brand worked about the same as gunk.
|
![]() |
![]() |
![]() |
#12 |
69 Fleetside
![]() Join Date: Mar 2009
Location: Lake Stevens, WA
Posts: 333
|
Re: Degreasing
|
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,507
|
Re: Degreasing
I've had good luck with Oil Eater. You can find it at parts houses and sometimes at Costco. After you scrape the heavy stuff off spray it on, let it set for a few minutes and wash it off at the car wash or sometimes with a hose. It works great for grease spots on cement floors too. Some of the shops up here are using it in their hot tanks instead of caustic as it is biodegradable.
|
![]() |
![]() |
![]() |
#14 |
Moderator
![]() Join Date: May 2007
Location: Southern Cal
Posts: 20,005
|
Re: Degreasing
If you can remove the part, I usually submerge it in a tub full of Purple Power de-greaser and let it soak a few days. Whatever is stuck to the part will come off like butter.
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man |
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Oct 2007
Location: Valley Springs, Ca
Posts: 857
|
Re: Degreasing
I tried everything possible to clean mine and the only thing that worked was scraping the thick crap off and then taking a solvent brush and a little gas in a can cleaned the hell out of it better then anything else I found.
|
![]() |
![]() |
![]() |
#16 |
HickTown
Join Date: Apr 2009
Location: ANDOVER, Kansas
Posts: 355
|
Re: Degreasing
anyone spray that cheapo oven cleaner on the motor and use it like engine degreaser??
__________________
1993 Ford Mustang Vert w/ 2.3 1969 Chevy C/10 w/350 1968 Chevy C-20 w/250 1976 Dodge Aspen W/ 225 2000 Toyota Tundra w/4.7 1987 Dodge Ram D-100 w/360 255/70-15 ___________ (oo)══╬══(oo) ‾‾‾‾‾‾‾‾‾‾‾ |
![]() |
![]() |
![]() |
#17 |
Man of Mini-Talents
Join Date: Sep 2009
Location: Oklahoma City, OK
Posts: 4,295
|
Re: Degreasing
Sand blast it.
|
![]() |
![]() |
![]() |
#18 |
Senior Member
Join Date: Jan 2007
Location: central pa
Posts: 428
|
Re: Degreasing
I've had the best luck with a puddy knife, easy off and a hydorspray/carwash. It works better than engine cleaner. Good luck BBO
__________________
![]() ![]() |
![]() |
![]() |
![]() |
#19 |
Registered User
Join Date: Feb 2009
Location: OKC OK
Posts: 489
|
Re: Degreasing
Castrol Super Clean is good but kinda spendy, So is Simple Green, Oven Cleaner is good, But I gotta agree with the sandblasting as the best method!
__________________
"You can put lipstick on a pig, sure it's pretty pig, but it's still just a PIG... ![]() 71 ![]() |
![]() |
![]() |
![]() |
#20 |
Registered User
Join Date: Mar 2007
Location: Oregon
Posts: 109
|
Re: Degreasing
Oven cleaner is a great idea, thanks! Someone told me sandblasting is not very effective because the media either bounces off or gets stuck in the grease. True?
|
![]() |
![]() |
![]() |
#21 |
Registered User
Join Date: Jul 2009
Location: Russellville, Arkansas
Posts: 1,699
|
Re: Degreasing
Putty knife, old wire brush,new wire brush then paint thinner with heavy duty stiff parts cleaner brush, then citrus based soap cleaner and garden hose. Worked for me.
![]() ![]() Good luck. |
![]() |
![]() |
![]() |
#22 |
Senior Member
![]() Join Date: Jul 2008
Location: kennewick, WA
Posts: 1,506
|
Re: Degreasing
try using a steam cleaning pressure washer.... like a hotsy or hot jenny. they will take just about anything off when it comes to greasy, oily messes.
__________________
1965 c/10 swb 1969 c/10 lwb ![]() |
![]() |
![]() |
![]() |
#23 |
Grandpa in the rustmobile...
Join Date: Nov 2008
Location: Spokane WA/Viola TN
Posts: 11,422
|
Re: Degreasing
I used combo of pressure washer putty knife screwdriver sandblaster oven cleaner wire brush wire brush on a electric drill
id say HOT water would be great! sandblasting ate thru grease as long as it wasnt really thick for me i only had lil spots here and there....
__________________
John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4 |
![]() |
![]() |
![]() |
#24 |
Registered User
Join Date: Jun 2008
Location: South Florida
Posts: 11,375
|
Re: Degreasing
heavy duty degreaser and a pressure cleaner worked for me pretty well...then primered and painted...
![]()
__________________
Get your facts first, and then you can distort them as much as you please!!!!!. Sylvester's build thread >>>http://67-72chevytrucks.com/vboard/s...ht=big+rebuild |
![]() |
![]() |
![]() |
Bookmarks |
|
|