![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Aug 2009
Location: PA
Posts: 883
|
78 c10 clean fire wall help?!
i have a 78 c10
and was looking to make the fire wall clean. i dont mind the booster brake and master cylinder but i do have questions on how to put my heater under the dash or how do you move it? i still want to have heat, but not where you can see it. can this be done? has anyone done this? pictures? help? |
![]() |
![]() |
![]() |
#2 |
6.0 powered square
Join Date: Feb 2008
Location: Mesquite texas
Posts: 3,459
|
Re: 78 c10 clean fire wall help?!
if your not set on a original heater I would go with a moab heater
http://www.summitracing.com/parts/SUM-991102/ ![]() ![]() ![]()
__________________
Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 Last edited by flamingbig10; 08-21-2009 at 12:23 AM. |
![]() |
![]() |
![]() |
#3 | |
Registered User
Join Date: Aug 2009
Location: PA
Posts: 883
|
Re: 78 c10 clean fire wall help?!
Quote:
like what u took out. what you put in, where you mounted stuff, etc. Last edited by N2TRUX; 08-21-2009 at 11:08 PM. |
|
![]() |
![]() |
![]() |
#4 |
6.0 powered square
Join Date: Feb 2008
Location: Mesquite texas
Posts: 3,459
|
Re: 78 c10 clean fire wall help?!
a few, the new heater mounts in between the ash trash and glove box, part of the heater box is mounted to the hump on the firewall and the other is mounted to flat part of the firewall
![]() ![]() ![]()
__________________
Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 Last edited by flamingbig10; 08-21-2009 at 12:51 AM. |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Aug 2009
Location: PA
Posts: 883
|
Re: 78 c10 clean fire wall help?!
thanks. the heater u gave me a link to, is that the only thing i need? what about those two tubes that hook into it?
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Aug 2009
Location: PA
Posts: 883
|
Re: 78 c10 clean fire wall help?!
anyone?
|
![]() |
![]() |
![]() |
#7 |
6.0 powered square
Join Date: Feb 2008
Location: Mesquite texas
Posts: 3,459
|
Re: 78 c10 clean fire wall help?!
for the heater hoses I going to run some fitting, 2 short hoses from the heater to firewall and then from the firewall to the motor
__________________
Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: May 2009
Location: Sparks, NV
Posts: 913
|
Re: 78 c10 clean fire wall help?!
i ran the same summit heater, it works great but took a little adjusting to get it to fit where i wanted it. the only thing that i'm still trying to figure out is how to adapt the new heater to the original ducting. bottom line being that i need to be able to defrost my windshield in the winter.
sorry i don't have a picture, but i pretty much mounted mine in the same location as flamingbig10, except with the vents facing upward.
__________________
Greg 1974 GMC 1/2 Ton SWB Fleetside L33 5.3/4l65e .................__
............._____l __\__ ..............l_(O)_ l___(O)] |
![]() |
![]() |
![]() |
Bookmarks |
|
|