Help With 283 Specs - The 1947 - Present Chevrolet & GMC Truck Message Board Network

SierraMtns · 03-27-2015, 11:55 PM

The 283 in my 67 stepper has about 400 miles on it since the rebuild. I know some of the specs from the PO. Can't find build sheets in all the papers and the machine shop closed when the owner retired. Trying to figure out some of the details without digging really deep into it.

The PO said to run 91 octane gas. Was told the heads are the "fuelie" 58 cc heads. I don't have any numbers off the heads but it would be easy to pull a valve cover for numbers. I did a vacuum test at idle and it was 16" lbs. Not sure if this would be expected with a RV cam? Also, would there be a way to check the overall compression ratio?

Here are the details I know.

283 block #3849852
Bored 0.40 over
RV cam (Not sure specs on cam)

Thanks

SierraMtns · 03-28-2015, 01:07 PM

ttt

SierraMtns · 03-30-2015, 04:14 PM

Ok I got more numbers off the block.

Here is the number on the pad infont of the passagner head.

F0124D

Anyone have a old GM book they can look up the number for me?

MARKDTN · 03-30-2015, 04:55 PM

You need a casting number from the head(s) to get much info. The F0124D does not help. Perhaps get the casting number off the rear of the block below the distributor.

SierraMtns · 03-30-2015, 05:00 PM

Quote:

Originally Posted by SierraMtns

The 283 in my 67 stepper has about 400 miles on it since the rebuild. I know some of the specs from the PO. Can't find build sheets in all the papers and the machine shop closed when the owner retired. Trying to figure out some of the details without digging really deep into it.

The PO said to run 91 octane gas. Was told the heads are the "fuelie" 58 cc heads. I don't have any numbers off the heads but it would be easy to pull a valve cover for numbers. I did a vacuum test at idle and it was 16" lbs. Not sure if this would be expected with a RV cam? Also, would there be a way to check the overall compression ratio?

Here are the details I know.

283 block #3849852
Bored 0.40 over
RV cam (Not sure specs on cam)

Thanks

Quote:

Originally Posted by MARKDTN

You need a casting number from the head(s) to get much info. The F0124D does not help. Perhaps get the casting number off the rear of the block below the distributor.

Its in my first post.

**jocko** · 03-30-2015, 08:47 PM

3849852: 57-66 283 with 2 bolt mains - very common, recurring block casting

F0124D:
F0124 = Flint Plant, Jan 24 build

"D" provides the best clue - I show that as either a:
1958 185 hp, 2bbl 283with powerglide, available on cars and trucks (note your mechanic said you had 58 fuelie heads...)
or
1960 170 hp, 2bbl 283 with powerglide, available on cars and trucks

Hope that helps.

SierraMtns · 03-30-2015, 10:05 PM

Quote:

Originally Posted by jocko

3849852: 57-66 283 with 2 bolt mains - very common, recurring block casting

F0124D:
F0124 = Flint Plant, Jan 24 build

"D" provides the best clue - I show that as either a:
1958 185 hp, 2bbl 283with powerglide, available on cars and trucks (note your mechanic said you had 58 fuelie heads...)
or
1960 170 hp, 2bbl 283 with powerglide, available on cars and trucks

Hope that helps.

Cool thank you sir. This was the info I was looking for.

Could you look up my heads?

Here are the numbers. Passenger side.

#8884520

Middle of head shows. GM 37

Back of the head shows. F307

Thanks

**jocko** · 03-30-2015, 11:03 PM

Can't find 8884520, but recommend re-check and see if leading digit is a "3"
3884520 = 1960-1967 283, 60cc chambers - 1.72 intake/1.50 exhaust
F307 is build date = May 30 (Edit: added '57) 57 -OR- 67 (perhaps 57 and still with their originally assigned duty on that '58 283...)

That's all I can find.

SierraMtns · 04-07-2015, 12:18 AM

Quote:

Originally Posted by jocko

3849852: 57-66 283 with 2 bolt mains - very common, recurring block casting

F0124D:
F0124 = Flint Plant, Jan 24 build

"D" provides the best clue - I show that as either a:
1958 185 hp, 2bbl 283with powerglide, available on cars and trucks (note your mechanic said you had 58 fuelie heads...)
or
1960 170 hp, 2bbl 283 with powerglide, available on cars and trucks

Hope that helps.

Quote:

Originally Posted by jocko

Can't find 8884520, but recommend re-check and see if leading digit is a "3"
3884520 = 1960-1967 283, 60cc chambers - 1.72 intake/1.50 exhaust
F307 is build date = May 30 (Edit: added '57) 57 -OR- 67 (perhaps 57 and still with their originally assigned duty on that '58 283...)

That's all I can find.

Yes it say "3". Thank you sir that info helped me a lot with figuring out details about the 283.

03-27-2015, 11:55 PM	#1
SierraMtns Registered User Join Date: Jun 2014 Location: Shingle Springs, CA Posts: 869	Help With 283 Specs The 283 in my 67 stepper has about 400 miles on it since the rebuild. I know some of the specs from the PO. Can't find build sheets in all the papers and the machine shop closed when the owner retired. Trying to figure out some of the details without digging really deep into it. The PO said to run 91 octane gas. Was told the heads are the "fuelie" 58 cc heads. I don't have any numbers off the heads but it would be easy to pull a valve cover for numbers. I did a vacuum test at idle and it was 16" lbs. Not sure if this would be expected with a RV cam? Also, would there be a way to check the overall compression ratio? Here are the details I know. 283 block #3849852 Bored 0.40 over RV cam (Not sure specs on cam) Thanks

03-28-2015, 01:07 PM	#2
SierraMtns Registered User Join Date: Jun 2014 Location: Shingle Springs, CA Posts: 869	Re: Help With 283 Specs ttt

03-30-2015, 04:55 PM	#4
MARKDTN Registered User Join Date: Jan 2011 Location: Chattanooga, TN Posts: 2,159	Re: Help With 283 Specs You need a casting number from the head(s) to get much info. The F0124D does not help. Perhaps get the casting number off the rear of the block below the distributor. __________________ '83 K20-TPI '73 C10 '79 C10-ex-diesel(SOLD) '07 Tahoe(Son driving) '14 Suburban-DD '71 C10-current project

03-30-2015, 08:47 PM	#6
jocko Senior Member Join Date: Oct 2009 Location: Godley, TX Posts: 17,976	Re: Help With 283 Specs 3849852: 57-66 283 with 2 bolt mains - very common, recurring block casting F0124D: F0124 = Flint Plant, Jan 24 build "D" provides the best clue - I show that as either a: 1958 185 hp, 2bbl 283with powerglide, available on cars and trucks (note your mechanic said you had 58 fuelie heads...) or 1960 170 hp, 2bbl 283 with powerglide, available on cars and trucks Hope that helps.

03-30-2015, 04:14 PM	#3
SierraMtns Registered User Join Date: Jun 2014 Location: Shingle Springs, CA Posts: 869	Re: Help With 283 Specs Ok I got more numbers off the block. Here is the number on the pad infont of the passagner head. F0124D Anyone have a old GM book they can look up the number for me?

03-30-2015, 11:03 PM	#8
jocko Senior Member Join Date: Oct 2009 Location: Godley, TX Posts: 17,976	Re: Help With 283 Specs Can't find 8884520, but recommend re-check and see if leading digit is a "3" 3884520 = 1960-1967 283, 60cc chambers - 1.72 intake/1.50 exhaust F307 is build date = May 30 (Edit: added '57) 57 -OR- 67 (perhaps 57 and still with their originally assigned duty on that '58 283...) That's all I can find. Last edited by jocko; 03-31-2015 at 12:52 AM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.