![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Jan 2019
Location: El Paso, TX
Posts: 28
|
Lower Steering Bearing ‘72 K10
Good Morning,
I am trying to replace the lower steering bearing on my K10 and it appears to be rusted on the shaft. Do I knock it off with a hammer? If not, what is the best method to remove the lower bearing? When installing the new lower bearing is it pressed on with an oversized socket and hammer? Sucks being a newbie! Tee Wolf
__________________
Tee Wolf |
![]() |
![]() |
![]() |
#2 |
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
![]()
Is it a 3 on the tree are auto? The lower bearing on a 3 speed 67 model is held by 2 screws at the bottom but not sure on a 72. Automatic Should have the bottom spring and retainer clip as in the picture.
If it is then yes you will have to beat it off are use a puller. I would use the puller first and if that didn't work beat it off soak it good first though before you do anything they are not press fit it should slide off. ![]()
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 ![]() Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
![]() |
![]() |
![]() |
#3 | |
Registered User
Join Date: Jan 2019
Location: El Paso, TX
Posts: 28
|
Quote:
|
|
![]() |
![]() |
![]() |
#4 |
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
![]()
Put it in a vise and have the bearing sitting on top but don't tighten it down just close it enough to hold the bearing on top. Then take a piece of wood and a big hammer and smack the rod end down. Spray it down good with some pentrating oil will help also. This is just me talking.
I just completely tore down a 3 speed column out of a 67 and nothing was seized up. Here is my thread on what I did. ![]() http://67-72chevytrucks.com/vboard/s...d.php?t=779844
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 ![]() Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
![]() |
![]() |
![]() |
#5 | |
Registered User
Join Date: Jan 2019
Location: El Paso, TX
Posts: 28
|
Quote:
|
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jan 2019
Location: El Paso, TX
Posts: 28
|
Re: Lower Steering Bearing ‘72 K10
Andy thank you very much.
Posted via Mobile Device |
![]() |
![]() |
![]() |
#7 |
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
![]()
If you look at my 67 shaft there is no bearing like yours on mine. It must be a year change but I wouldn't think it to be a press on fit though.
![]()
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 ![]() Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jan 2019
Location: El Paso, TX
Posts: 28
|
Re: Lower Steering Bearing ‘72 K10
Andy,
Thanks again for the advise. I completed the task, with your directions, yesterday without issue. Thanks again.
__________________
Tee Wolf |
![]() |
![]() |
![]() |
#9 | |
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
![]() Quote:
![]()
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 ![]() Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
|
![]() |
![]() |
![]() |
Bookmarks |
|
|