|
|
|
09-03-2003, 09:28 PM
|
#1 |
|
Registered User
Join Date: Aug 2001
Location: texas, usa
Posts: 194
|
door adjustment
i need to slide my door a little foward. i finished doing some work and noticed i had worked it back in the doorway a bit. looking at moving it back towards the front about an eighth of an inch.
any tips? i figure i should adjust it where the hinge bolts to the cab. should i start with the top hinge first? thanks for any advice. |
|
|
|
09-03-2003, 10:55 PM
|
#2 |
|
Registered User
Join Date: Jul 2003
Location: north of Phx AZ about 30 miles
Posts: 698
|
Ive had fair luck loosening all the bolts except one on the top one on the bottom and sliding the door around from there. Just mark where it is now so you can see what youve done and can go back to square one if it gets all higgly piggly.
__________________
Andy,Phx AZ '67 C-10 (Ahhh, done at last. Well there is that disk front end I want to put in and...) "23 C-Cab-sold '48 Ford 8N tractor(still working) '67 Scout(Now on the road) '70 MG B.-sold |
|
|
|
|
09-04-2003, 10:09 AM
|
#3 |
|
Registered User
Join Date: Jul 2002
Location: St. James, MO
Posts: 1,238
|
I hope you either have your fenders off or the handy, dandy special wrench for that job . . . .
__________________
'69 Longstep K-10: 327/SM465/T-221/Closed Knuckle Dana44/12-bolt. |
|
|
|
|
09-04-2003, 10:16 AM
|
#4 |
|
Account Suspended
 
Join Date: Jun 2003
Location: PA
Posts: 1,411
|
Palallin,
Do you know where to get that "Special Wrench" for the inner hinge bolts? Anybody know? |
|
|
|
|
09-04-2003, 11:02 AM
|
#5 |
|
Registered User
Join Date: Aug 2001
Location: SOMERSET KY.
Posts: 6,427
|
HIGGLY PIGGLY??
__________________
junkyardjohn 69 1 TON TOW TRUCK // 84 4WD CUCV BLAZER// 85 1 TON 4WD STAKE TRUCK// 86 M1031 5/4 TON 4WD CUCV// ALOT OF OLD TRUCKS FOR ONE OLD MAN TO DRIVE.  THERES ROOM FOR ALL OF GODS CREATURES RIGHT NEXT TO MY MASHED POTATOES//LIFE MEMBER OF P.E.T.A (PEOPLE EATING TASTY ANIMALS) DON'T RENT U-HAUL ALWAYS TELL THE TRUTH IT WILL AMAZE PART OF THE PEOPLE & ASTONISH THE REST |
|
|
|
|
09-04-2003, 02:16 PM
|
#6 |
|
Registered User
Join Date: Jul 2002
Location: St. James, MO
Posts: 1,238
|
A Chevy dealer with a pack-rat in the service department. It was exclusive to these trucks, I think.
__________________
'69 Longstep K-10: 327/SM465/T-221/Closed Knuckle Dana44/12-bolt. |
|
|
|
|
09-04-2003, 02:52 PM
|
#7 |
|
Can't kick the addiction!
Join Date: Jan 2002
Location: Riverton, CT 06065
Posts: 402
|
Anybody got a pic of the "special wrench"?
|
|
|
|
|
09-04-2003, 03:41 PM
|
#8 |
|
Registered User
Join Date: Jul 2002
Location: St. James, MO
Posts: 1,238
|
It's in the Service Manual. If no one does earlier, I'll try to scan an image this weekend and post it.
__________________
'69 Longstep K-10: 327/SM465/T-221/Closed Knuckle Dana44/12-bolt. |
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
