Core rad support frame - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chevy88 · 11-14-2009, 12:20 PM

Can some one tell me the distance between core rad support and frame? This will help in initially lining things up and possibly if I have rubber supports backwards as I wasn't paying attention again when I pulled it apart.

epashhans · 11-14-2009, 05:17 PM

Hey K, after looking at yours I believe there are two different setups...if you are going to the 67-68 front end. Check the two setups here...

Mounts

You can see the 60-68 is a different setup...and they have it pictured upside down (at least that is how mine was when I took it apart).

I put an orange line where the rad support will go, and the blue line is where the frame would be. And then on mine, those triangular pieces on the bottom were bent up so the nut could not spin off. Not sure if that was someones personal touch or if that is the way they came. I would guess that is the way its suppose to be.

As a side note, the LMC mag I have shows the setup you have...so I am not sure if it will work with that one or not...? Maybe someone else can chime in.

**seafoam68** · 11-14-2009, 05:58 PM

There is a difference in 67,68 and 69-72. The 67,68 have a smaller hole in the frame mount piece and use the mounts with the triangle shaped piece. The LMC catalog is not correct, as they show one mount for all years. Sorry, but mine is all apart right now, so I can't provide the distance between core and mount.

epashhans · 11-14-2009, 09:44 PM

Quote:

Originally Posted by seafoam68

There is a difference in 67,68 and 69-72. The 67,68 have a smaller hole in the frame mount piece and use the mounts with the triangle shaped piece. The LMC catalog is not correct, as they show one mount for all years. Sorry, but mine is all apart right now, so I can't provide the distance between core and mount.

Thats what I thought. Does my diagram with the colored lines look correct?

Mine is all apart as well!

**LockDoc** · 11-14-2009, 10:12 PM

-
The flat one goes between the core support and frame and the shoulder on it goes down in the hole in the frame mount. The cone shaped one goes on the bottom small end down.

You have them reversed....

LockDoc

westofb · 11-14-2009, 11:04 PM

Quote:

Originally Posted by LockDoc

-
The flat one goes between the core support and frame and the shoulder on it goes down in the hole in the frame mount. The cone shaped one goes on the bottom small end down.

You have them reversed....

LockDoc

I agree you have the rubbers reversed!

11-14-2009, 12:20 PM	#1
chevy88 Registered User Join Date: May 2007 Location: Southern, Saskatchewan Posts: 640	Core rad support frame Can some one tell me the distance between core rad support and frame? This will help in initially lining things up and possibly if I have rubber supports backwards as I wasn't paying attention again when I pulled it apart. __________________ Kerry My build thread. http://67-72chevytrucks.com/vboard/s....php?p=3657823 1971 Chev SWB with 68 nose, 6.2 diesel th350, and 3.73 rear gears 1988 Chev Extendacab 2010 Honda VT1300CS Sabre 2005 Buick Rendezvous wife's ride

11-14-2009, 05:17 PM	#2
epashhans Registered User Join Date: Jul 2009 Location: MT Posts: 319	Re: Core rad support frame Hey K, after looking at yours I believe there are two different setups...if you are going to the 67-68 front end. Check the two setups here... Mounts You can see the 60-68 is a different setup...and they have it pictured upside down (at least that is how mine was when I took it apart). I put an orange line where the rad support will go, and the blue line is where the frame would be. And then on mine, those triangular pieces on the bottom were bent up so the nut could not spin off. Not sure if that was someones personal touch or if that is the way they came. I would guess that is the way its suppose to be. As a side note, the LMC mag I have shows the setup you have...so I am not sure if it will work with that one or not...? Maybe someone else can chime in. Attached Images __________________ '67 C-10 Shorty - 454, 5spd, and speed holes!

11-14-2009, 05:58 PM	#3
seafoam68 Senior Member Join Date: Oct 2009 Location: Chattanooga, TN Posts: 259	Re: Core rad support frame There is a difference in 67,68 and 69-72. The 67,68 have a smaller hole in the frame mount piece and use the mounts with the triangle shaped piece. The LMC catalog is not correct, as they show one mount for all years. Sorry, but mine is all apart right now, so I can't provide the distance between core and mount.

11-14-2009, 10:12 PM	#5
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,518	Re: Core rad support frame - The flat one goes between the core support and frame and the shoulder on it goes down in the hole in the frame mount. The cone shaped one goes on the bottom small end down. You have them reversed.... LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - Last edited by LockDoc; 11-14-2009 at 10:14 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.