![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Senior Member
![]() Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,508
|
Ignition switch removal
I am trying to remove my ignition switch. I don't have a key, nor do I have a door key. I am trying to remove the bezel and it just keeps turning.
HELP!
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jun 2011
Location: Osceola, Ia
Posts: 2,017
|
Re: Ignition switch removal
That lock cylinder has to come out for the bezel to be threaded off. But this does usually require a key w/ a paper clip or similar. Sounds like it may need drilled. Something I've had to do. Member LocDock may chime in with a better idea..
__________________
Shawn 68 chevy K/20 05 chevy 3/4 4x4 71 short step-sold ![]() 71 chevy Beauville van My build. http://67-72chevytrucks.com/vboard/s...d.php?t=633039 |
![]() |
![]() |
![]() |
#3 |
The Older Generation
![]() ![]() ![]() Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,490
|
Re: Ignition switch removal
-
The first thing I would do is to pull the passengers door lock out and see if there is a code number stamped into it. If there is take it to a locksmith and have him cut you a key. If the locks are all original the key will fit the ignition. If you don't have a locksmith close PM me the code number and I will cut you a key and send it to you for 5 bucks. If there is no code number on it, the door lock can still be disassembled and de-coded to cut a key. The destructive methods would be a last resort for me. Picture shows the location of the code number. LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
![]() |
![]() |
![]() |
#4 |
Senior Member
![]() Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,508
|
Re: Ignition switch removal
My truck didn't come with doors
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
![]() |
![]() |
![]() |
#5 |
The Older Generation
![]() ![]() ![]() Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,490
|
Re: Ignition switch removal
Then you have a problem. Basically your only option is to drill it out. If you can get the lock cylinder out without damaging the switch you can re-use all of the parts. If you drill it just don't drill too deep. Put a piece of masking tape up about 3/4 -7/8 of an inch on the bit and don't go any deeper than that. Start with a small bit and work your way up, take it slow because it will want to grab.
LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
![]() |
![]() |
![]() |
#6 |
Senior Member
![]() Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,508
|
Re: Ignition switch removal
How big a hole should I end up with before the cylinder comes out?
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
![]() |
![]() |
![]() |
Bookmarks |
|
|