CA Parting out 69 C20 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ScottG · 10-05-2012, 11:00 PM

Got what's left of a '69 C20 to part out. Cab and bed sheet metal was junk, so that's gone to scrap metal. Here's what I have off so far:

Headlight trim, straight light surface rust sold

Fender emblems, some over spray, easily cleanable SOLD

Front turn signals with lenses sold

Gauge cluster, nice printed circuit, everything works SOLD

4 row radiator clamps, rubber good. sold

Headlight buckets with springs and adjusters sold

Tailgate trunions 10.00 shipped

Ball bearing ashtray, crappy paint job, but works great! 10.00 shipped

Lighter, headlight switch, and wiper switch with knobs, headlight switch looks
fairly new. tiny bit of over spray on lighter trim that will clean right off. All
in working condition SOLD

Hood latch with support. Nice and straight, works fine 25.00 shipped

Brake booster w/ proportioning valve and master cylinder. For drum brakes,
works fine. SOLD

High hump trans tunnel. Very nice!!! With bolts SOLD

Saddle seat belts, needs cleaning, pitting on chrome on 1. 1 buckle has
a little cracking SOLD

Saddle visors, very nice SOLD

Aqua blue/ green visors, very nice SOLD

Chrome 1 wire alternator, working condition, don't know the
amperage. dsSOLD

4 row radiator. Aftermarket, appears to be recently replaced. Fins are
perfect. Very nice. SOLD

Left fender, very clean, no dents, cup is good. PO screwed front molding in with 2 small screws, otherwise really nice shape SOLD

Right fender, same screw holes, but 4 instead of 2. Cup has rust, but the rest
is very nice. SOLD

I'll be adding more as I get it apart. If you don't see it, ask, I might have it!!

**too much stuff** · 10-05-2012, 11:57 PM

I will take the emblems if the studs are intact.
Engine stands?

ScottG · 10-06-2012, 12:02 AM

Quote:

Originally Posted by too much stuff

I will take the emblems if the studs are intact.
Engine stands?

They are intact, with the nuts on them as well. I have 2 sets of small block engine stands. No big block, as this truck was converted at some point.
pm sent on the emblems.
thanks, Scott

ScottG · 10-06-2012, 07:44 PM

Quote:

Originally Posted by too much stuff

I will take the emblems if the studs are intact.
Engine stands?

PM sent on the hood emblem

**gmc 2500 4x4** · 10-06-2012, 05:54 AM

i'll take brake booster

**WETOWM** · 10-06-2012, 08:08 AM

I need the part of the floor where the high hump cover bolt to if you still have the cab ?

ScottG · 10-06-2012, 11:03 AM

Quote:

Originally Posted by WETOWM

I need the part of the floor where the high hump cover bolt to if you still have the cab ?

No sorry. I cut it up because it was badly rusted. I'll keep an eye out though.

bollybib · 10-06-2012, 12:03 PM

I'll take the seat belts. PM me your payment info.

ScottG · 10-06-2012, 12:18 PM

Quote:

Originally Posted by bollybib

i'll take the seat belts. Pm me your payment info.

pm sent

ScottG · 10-06-2012, 10:59 AM

Quote:

Originally Posted by gmc 2500 4x4

i'll take brake booster

Pm sent.

**gmc 2500 4x4** · 10-06-2012, 05:21 PM

Quote:

Originally Posted by gmc 2500 4x4

i'll take brake booster

payment sent<<<

ScottG · 10-06-2012, 05:29 PM

Quote:

Originally Posted by gmc 2500 4x4

payment sent<<<

Thanks Paul.
Scott

**burb71** · 10-06-2012, 06:24 PM

Do you still have the big block power steering hose

ScottG · 10-06-2012, 06:46 PM

Quote:

Originally Posted by burb71

Do you still have the big block power steering hose

You know, I might. The p/s bracket doesn't look right to me for a small block, so the PO might have used the original on it. I'll get back to you on this.

ScottG · 10-07-2012, 04:41 PM

Quote:

Originally Posted by burb71

Do you still have the big block power steering hose

It appears to be a small block set up. I can't identify the bracket yet to be sure.
It did have BB engine towers though.

**gmc 2500 4x4** · 10-07-2012, 07:15 PM

Quote:

Originally Posted by ScottG

Thanks Paul.
Scott

get a tracking # when you ship please....thanx, paul

ScottG · 10-07-2012, 10:26 PM

Quote:

Originally Posted by gmc 2500 4x4

get a tracking # when you ship please....thanx, paul

I'll have it for you tomorrow, no prob.

**cericd** · 10-06-2012, 10:27 AM

Interested in the lighter and switch set. Do you have the wiring harness for the lighter? Is the headlight switch a gm part?
Posted via Mobile Device

ScottG · 10-06-2012, 11:02 AM

Quote:

Originally Posted by cericd

Interested in the lighter and switch set. Do you have the wiring harness for the lighter? Is the headlight switch a gm part?
Posted via Mobile Device

I do have the harness, I'll throw that in. Switch looks aftermarket, but that's not a bad thing. Put 2 Delco switches in my truck, 1 took a dump after 2 months, and the replacement was DOA right out of the box!

**cericd** · 10-06-2012, 01:00 PM

Hey scottg I was mostly concerned with the knobs looking the same including the brushed metal inserts. Do they? Would all the parts clean up real nice? Does the lighter assembly have a light? Just curious. Thanks
Posted via Mobile Device

ScottG · 10-06-2012, 01:32 PM

Quote:

Originally Posted by cericd

Hey scottg I was mostly concerned with the knobs looking the same including the brushed metal inserts. Do they? Would all the parts clean up real nice? Does the lighter assembly have a light? Just curious. Thanks
Posted via Mobile Device

All knobs are identical, they will clean up nicely. Lighter does not have a light.

Rgthoma · 10-06-2012, 06:01 PM

I'm looking for a bellhousing #3925505

BlackhillsHD · 10-06-2012, 06:10 PM

I will take the cluster. PM me with payment info

ScottG · 10-06-2012, 06:44 PM

Quote:

Originally Posted by BlackhillsHD

I will take the cluster. PM me with payment info

PM sent. Thanks, Scott.

ScottG · 10-06-2012, 06:43 PM

Quote:

Originally Posted by Rgthoma

I'm looking for a bellhousing #3925505

I have one, but not sure of the #. I'll check when I get home.

10-05-2012, 11:00 PM	#1
ScottG Registered User Join Date: Feb 2012 Location: Ventura,Ca Posts: 745	Parting out 69 C20 PRICES LOWERED!!! Got what's left of a '69 C20 to part out. Cab and bed sheet metal was junk, so that's gone to scrap metal. Here's what I have off so far: Headlight trim, straight light surface rust sold Fender emblems, some over spray, easily cleanable SOLD Front turn signals with lenses sold Gauge cluster, nice printed circuit, everything works SOLD 4 row radiator clamps, rubber good. sold Headlight buckets with springs and adjusters sold Tailgate trunions 10.00 shipped Ball bearing ashtray, crappy paint job, but works great! 10.00 shipped Lighter, headlight switch, and wiper switch with knobs, headlight switch looks fairly new. tiny bit of over spray on lighter trim that will clean right off. All in working condition SOLD Hood latch with support. Nice and straight, works fine 25.00 shipped Brake booster w/ proportioning valve and master cylinder. For drum brakes, works fine. SOLD High hump trans tunnel. Very nice!!! With bolts SOLD Saddle seat belts, needs cleaning, pitting on chrome on 1. 1 buckle has a little cracking SOLD Saddle visors, very nice SOLD Aqua blue/ green visors, very nice SOLD Chrome 1 wire alternator, working condition, don't know the amperage. dsSOLD 4 row radiator. Aftermarket, appears to be recently replaced. Fins are perfect. Very nice. SOLD Left fender, very clean, no dents, cup is good. PO screwed front molding in with 2 small screws, otherwise really nice shape SOLD Right fender, same screw holes, but 4 instead of 2. Cup has rust, but the rest is very nice. SOLD I'll be adding more as I get it apart. If you don't see it, ask, I might have it!! __________________ '67 C20 LBW Last edited by ScottG; 11-27-2012 at 01:30 PM. Reason: MARK SOLD

10-05-2012, 11:57 PM	#2
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,765	Re: Parting out 69 C20 I will take the emblems if the studs are intact. Engine stands? __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

10-06-2012, 05:54 AM	#5
gmc 2500 4x4 Senior Member Join Date: Mar 2012 Location: ripley ny Posts: 2,958	Re: Parting out 69 C20 i'll take brake booster

10-06-2012, 08:08 AM	#6
WETOWM Senior Member Join Date: Jun 2011 Location: ST LOUIS MO Posts: 2,114	Re: Parting out 69 C20 I need the part of the floor where the high hump cover bolt to if you still have the cab ?

10-06-2012, 12:03 PM	#8
bollybib Registered User Join Date: Nov 2010 Location: Carlsbad, CA Posts: 1,584	Re: Parting out 69 C20 I'll take the seat belts. PM me your payment info. __________________ - Jim - My Daily Driver is a 1969 Chevrolet Custom/20 Fleetside 350/TH400/Eaton H052 4.10 and its Project thread is here http://67-72chevytrucks.com/vboard/s...d.php?t=456911

10-06-2012, 06:24 PM	#13
burb71 Active Member Join Date: Oct 2002 Location: Ft. Myers, Fl Posts: 1,716	Re: Parting out 69 C20 Do you still have the big block power steering hose

10-06-2012, 10:27 AM	#18
cericd Senior Member Join Date: Jan 2012 Location: Texan, back in TX Posts: 2,158	Re: Parting out 69 C20 Interested in the lighter and switch set. Do you have the wiring harness for the lighter? Is the headlight switch a gm part? Posted via Mobile Device

10-06-2012, 01:00 PM	#20
cericd Senior Member Join Date: Jan 2012 Location: Texan, back in TX Posts: 2,158	Re: Parting out 69 C20 Hey scottg I was mostly concerned with the knobs looking the same including the brushed metal inserts. Do they? Would all the parts clean up real nice? Does the lighter assembly have a light? Just curious. Thanks Posted via Mobile Device

10-06-2012, 06:01 PM	#22
Rgthoma Registered User Join Date: Sep 2012 Location: Albuquerque, NM Posts: 8	Re: Parting out 69 C20 I'm looking for a bellhousing #3925505

10-06-2012, 06:10 PM	#23
BlackhillsHD Registered User Join Date: Nov 2011 Location: Rapid City SD Posts: 140	Re: Parting out 69 C20 I will take the cluster. PM me with payment info __________________ 1970 : Chevy: K20 "Frank the Tank" 6.0 LS, 4L80E, 14 bolt, and Dana 44 1970 K5 Blazer CST 350, TH350, Np205, Dana 60 and 14 bolt General Motors Master Certified wrench swinger ASE certified Master auto tech Instructor of Automotive Technology



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.