![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Dec 2010
Location: Reno NV
Posts: 53
|
![]()
I cannot seem to figure out how to wire the fuel leveler inside of the fuel cell. Ever since I got the truck fired up, the gas gauge went all the way up past full.
I looked into it, and I just added a new ground from the battery to the frame thinking that was the problem and it wasn't. I've tried multiple locations for the ground with no luck. even with running an external jump wire just to test it the leveler still wont read. so I broke out the wire tester and the factory location for the gas tank wire barely lights up on the indicator as saying a weak source. so I tap out of the ignition after starting it up to make sure I had a constant and it's still won't read. I've tried everything I could and it's very frustrating. How did you set yours up? What did you do with the factory wire? Where did you ground it? Am I missing something here or is this just a simple stupid fix?? Thanks Posted via Mobile Device Posted via Mobile Device |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Aug 2010
Location: Edwards, CA
Posts: 7,503
|
Re: Help with wiring boyd rear fuel cell!?
Is the sender the correct ohm value for you stock gauge? The factory fuel gauge system is really simple. B+ to the gauge on one side and the sender sense wire on the other. The sender has the sense wire and a local ground. Did you ground it to the chassis or just the tank? Did you extend the original sense wire back to your new sender or did you just tap into it. Are you using a factory service manual schematic or something simplified?
Vette Vet is really good with these and here is a thread he posted to that should be very helpful. http://67-72chevytrucks.com/vboard/s...d.php?t=327643
__________________
Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID ** Blazer SPID ** Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders ** Do you have a 1972 Plaid Pickup? ** Plaid Blazer ** Plaid Suburban Last edited by SS Tim; 04-26-2013 at 09:15 PM. |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jul 2010
Location: central michigan
Posts: 1,193
|
Re: Help with wiring boyd rear fuel cell!?
I was also hoping the Boyd tank would come with directions .
Posted via Mobile Device |
![]() |
![]() |
![]() |
#4 | |
Registered User
Join Date: Dec 2012
Location: Altoona Iowa
Posts: 481
|
Re: Help with wiring boyd rear fuel cell!?
Quote:
|
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jul 2010
Location: central michigan
Posts: 1,193
|
Re: Help with wiring boyd rear fuel cell!?
is your sender marked + & - ?
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Dec 2010
Location: Reno NV
Posts: 53
|
Re: Help with wiring boyd rear fuel cell!?
thank you for all the responses, after troubleshooting it today I finally got the wiring correct.
upon doing more research, I saw other members say a lot of times the float on the leveler gets stuck, and if your gas gauge goes way past full chances are that's the problem. So I took out the leveler out of the fuel cell inspected the float and put it back in, fired the truck up still with the same issue. it is not labeled positive negative, but from what I saw on other posts was the big one in the center is positive, and the small one on the side is negative. When I took it out of the fuel cell neither of them were labeled. But the negative had no connection underneath so it had to be the ground So I finally have the connection right, why will my factory fuel gauge still not work? Any other ideas? Posted via Mobile Device |
![]() |
![]() |
![]() |
#7 | |
Msgt USAF Ret
![]() ![]() Join Date: Jan 2005
Location: Kalamazoo, Michigan
Posts: 8,714
|
Re: Help with wiring boyd rear fuel cell!?
Quote:
Look on your fuse panel on the right or left end about center and you should see a terminal marked "FUEL", Is there a tan wire connected there? If not that is where the center terminal from the tank sender is supposed to go. If the wire is there then Pull it off and run a temporary wire from there to a good ground and turn the key on and watch the fuel gauge. It should go to empty or below. This checks the wiring from the fuse panel to the gauge. Plug the tan wire back onto the terminal and check it for a broken spot back to the sender. Then check the sender for a good ground to the tank and the tank for a good ground to the frame. All the wiring from the fuse panel fuel terminal back to the sender and to the frame is on the negative side of the circuit. Do not apply any positive voltage to this circuit. It could result in an explosion inside the fuel tank Post back with the results. VV
__________________
VetteVet metallic green 67 stepside 74 corvette convertible 1965 Harley sportster 1995 Harley wide glide Growing old is hell, but it beats the alternative. |
|
![]() |
![]() |
![]() |
#8 | |
Registered User
Join Date: Dec 2010
Location: Reno NV
Posts: 53
|
Re: Help with wiring boyd rear fuel cell!?
Quote:
In the fuse panel where the factory tank was hooked up to "Fuel" is putting out little to no power, barely lights up the test light when ignition is turned on. So I took the fuse panel off last night and tested to wire directly with the same results, so the feed to my "Fuel" terminal is no good. I switched it to an open (not used) one on the bottom of the fuse panel that only gets power off the ignition. Is this not ok? I'm going to play around with it later tonight or tomorrow. Thanks |
|
![]() |
![]() |
![]() |
#9 | |
Msgt USAF Ret
![]() ![]() Join Date: Jan 2005
Location: Kalamazoo, Michigan
Posts: 8,714
|
Re: Help with wiring boyd rear fuel cell!?
Quote:
The reason you're not reading any voltage on the fuel terminal in the fuse panel is because the resistor on the back of the fuel gauge drop the voltage low enough to protect the gauge and the sending unit resistor.
__________________
VetteVet metallic green 67 stepside 74 corvette convertible 1965 Harley sportster 1995 Harley wide glide Growing old is hell, but it beats the alternative. |
|
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Dec 2010
Location: Reno NV
Posts: 53
|
Re: Help with wiring boyd rear fuel cell!?
[QUOTE=VetteVet;6044878]The biggest cause for the fuel gauge going past full is that the tank sender wire is disconnected from the circuit. Or the sender is not grounded to the frame.
Look on your fuse panel on the right or left end about center and you should see a terminal marked "FUEL", Is there a tan wire connected there? If not that is where the center terminal from the tank sender is supposed to go. If the wire is there then Pull it off and run a temporary wire from there to a good ground and turn the key on and watch the fuel gauge. It should go to empty or below. This checks the wiring from the fuse panel to the gauge. So I removed the tan wire from the other ignition terminal I had mentioned previously, No explosions haha. I did the test you mentioned about a temporary wire and the gas gauge wen't down to empty like you said. Soon as I put it back it went way past full and that's where it's staying again. I've check the wire and it is fine without any kinks or anything, I have the leveler grounded to the small crossbrace that has to be moved forward to fit these tanks, do you think this ground is not sufficient? I appreciate the help and I know it's only two wires yet something so small and dumb is holding up my entire project. Once the gauge works I can put the bed back on |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Aug 2010
Location: Edwards, CA
Posts: 7,503
|
Re: Help with wiring boyd rear fuel cell!?
VetteVet, You have patience, but then most people don't realize a test light does not begin "tell all" even on these simple truck systems.
Funny thing is this reminds me about a mechanic who could not diagnose a power window problem on a customer's old Mercedes sedan. Everywhere he tried his tester into the "wires" there was no power. Three days later someone pointed out they were vacuum operated windows. He ended up replacing a lot of vacuum hose.
__________________
Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID ** Blazer SPID ** Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders ** Do you have a 1972 Plaid Pickup? ** Plaid Blazer ** Plaid Suburban |
![]() |
![]() |
![]() |
#12 | |
Msgt USAF Ret
![]() ![]() Join Date: Jan 2005
Location: Kalamazoo, Michigan
Posts: 8,714
|
Re: Help with wiring boyd rear fuel cell!?
Quote:
I got you on my friends list.
__________________
VetteVet metallic green 67 stepside 74 corvette convertible 1965 Harley sportster 1995 Harley wide glide Growing old is hell, but it beats the alternative. |
|
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,005
|
Re: Help with wiring boyd rear fuel cell!?
Again, is your sender using the correct ohms value? O-90, if not then it would read full when empty. Take the sender out, leave the ground and wire to the fuse block on it, then move the float level arm up and down, SLOWLY! Do you see any movement on the gauge. If you want you can take the sender up by the fuse block. Run a wire from the + terminal on the sender to the spot on the block marked fuel. Then run a wire from the negative to the a (good) ground somewhere. Then see if the gauge moves at all. Take a picture of your wiring for us if you can.
You may have blown the resistor when you gave the sender full power. So you may have to buy a new resistor/ or sending unit. Posted via Mobile Device
__________________
1972 C20 Suburban- Big Blue Betty '56 Chevy Bel Air Sedan- Frame up Restoration -What would you attempt to achieve if you knew you could not fail?- -I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door- R.I.P. EAST SIDE LOW LIFE |
![]() |
![]() |
![]() |
#14 |
Registered User
Join Date: Apr 2004
Location: Las Vegas, NV
Posts: 2,188
|
Re: Help with wiring boyd rear fuel cell!?
Currently having the same issue with mine. I am 100% sure that everything is wired correctly. Upon closer inspection, the printed circuit seems to have shorted and is a bit burnt going to the gauge.
May be worth taking a look at. I can confirm that the sender supplied with Boyd's is the correct 0-90 ohm.
__________________
RIP EastSideLowLife '72 C20 SWB convert. 5 lug, LS1/4l60e |
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Oct 2012
Location: vancouver washington
Posts: 89
|
Re: Help with wiring boyd rear fuel cell!?
After turning the key off Remove the center wire at the sender and then turn the key on your fuel gauge should go past full, then put the same wire to a good ground it should go to empty if this works your gas gauge and line back to the fuel gauge is good and you know you either have a ground problem at the sender or the wrong OHMS value of the sender, or the sender is bad.
|
![]() |
![]() |
![]() |
#16 | |
Registered User
Join Date: Dec 2010
Location: Reno NV
Posts: 53
|
![]() Quote:
Here's the mind boggling part. When I place it back in the fuel cell to mount it, it goes way past full again. There's about 6-7 gallons out of the 17 gallon capacity. So it seems my wiring works correctly until I try to mount it. How is this possible? This has literally delayed my progress two weeks now. I don't have an ohms tester, sounds like I'm gunna have to get one. Sorry for dragging this out. Its really frustrating Posted via Mobile Device |
|
![]() |
![]() |
![]() |
#17 | |
Msgt USAF Ret
![]() ![]() Join Date: Jan 2005
Location: Kalamazoo, Michigan
Posts: 8,714
|
Re: Help with wiring boyd rear fuel cell!?
Quote:
You solved your own problem when you ran the temporary ground and the gauge worked. When you mounted the sender back in the tank you lost the ground. Either you changed wires like Jorgensensc said or the sender flange is insulated from the tank body, or possibly the tank is not grounded back to the battery. Connect the temporary ground wire back on the sender flange and see if the gauge reads the right amount.
__________________
VetteVet metallic green 67 stepside 74 corvette convertible 1965 Harley sportster 1995 Harley wide glide Growing old is hell, but it beats the alternative. |
|
![]() |
![]() |
![]() |
#18 |
Registered User
Join Date: Dec 2010
Location: Reno NV
Posts: 53
|
Re: Help with wiring boyd rear fuel cell!?
so I know its been awhile the latest update because I couldn't get it to work, I contacted Boyd welding about the issues I was having. They told me that the fuel leveler was from classic instruments after calling classic instruments describing the situation they told me to send it in and they would test it.
just got the call today, turns out the leveler was bad. talk about a waste of time and a month of holding a project up. on a positive note they're going to send me a replacement one at no cost to me. So I can't complain. Thanks for everyones advice though Jon Posted via Mobile Device |
![]() |
![]() |
![]() |
#19 |
Registered User
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,005
|
Re: Help with wiring boyd rear fuel cell!?
2 questions:
1st, when you moved the level arm up and down, did it appear to correspond with the gauge as far as level? Ex. Halfway up registers half a tank on gauge. 2nd, when you hooked the wires back up before putting it in the tank, when it worked the second time, did you use the new temp ground or the other ground you were using before? I seriously think you have a grounding issue. Posted via Mobile Device
__________________
1972 C20 Suburban- Big Blue Betty '56 Chevy Bel Air Sedan- Frame up Restoration -What would you attempt to achieve if you knew you could not fail?- -I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door- R.I.P. EAST SIDE LOW LIFE |
![]() |
![]() |
![]() |
#20 |
Registered User
Join Date: Aug 2010
Location: Edwards, CA
Posts: 7,503
|
Re: Help with wiring boyd rear fuel cell!?
That is an unexpected turn of events. The level sender worked outside the tank but not mounted wounder what the root problem is, did they tell you? But you have or will have a new sender soon so that is a good thing.
__________________
Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID ** Blazer SPID ** Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders ** Do you have a 1972 Plaid Pickup? ** Plaid Blazer ** Plaid Suburban |
![]() |
![]() |
![]() |
Bookmarks |
|
|