![]() |
|
![]() |
#1 |
Registered User
Join Date: Aug 2001
Location: escondido, ca 92026
Posts: 1,222
|
hood hinge question
My hood wont go all the way down at the back, and I've done all the adjusting I can (I think)... my hinges are the originals from 72.
The hinge pivots seem tight, but I haven't had the springs off to really test them well. Should I just be able to replace the springs to remedy the problem, or am I better off getting new hinges and springs..??? Thanks for any input...
__________________
'72 short step, 350, 700R4, tilt, ps, pdb, a/c, lowered coils, etc., other work in progress... San Diego, CA 72 Stepside Project |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jun 2002
Location: Knoxville Tenn.
Posts: 3,058
|
Re: hood hinge question
Oil all of the pins and see what happens.
__________________
56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer |
![]() |
![]() |
![]() |
#3 | |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,477
|
Re: hood hinge question
Quote:
![]()
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
![]() |
![]() |
![]() |
#4 |
Senior Member
![]() ![]() Join Date: Jan 2005
Location: CA
Posts: 5,522
|
Re: hood hinge question
If oiling the hinges doesn't get you all the way there, try loosening the two rear-most bolts that attach the hinge to the fender, and lower the back of the hinge. Then retighten the hinge. If you do it too much, the hood will be too tight in the back. If that doesn't give you enough adjustment, leave the back bottom bolt tight and loosen the other two bolts and raise the front of the hinge and retighten the bolts. If the hinges are high in the front and low in the back, this will give you the maximum amount of adjustment.
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Nov 2000
Location: Huntsville Ontario Canada
Posts: 4,052
|
Re: hood hinge question
I third the "oiling".
__________________
1968 Suburban numbers matching all original truck now equipped with 6.0/4L80 on Accuair http://67-72chevytrucks.com/vboard/s...d.php?t=625017 1967 C/20 6.0/4L80 Roofing Truck 1990 V2500 Suburban "Plow Truck" 2005 TAHOE DD |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Aug 2001
Location: escondido, ca 92026
Posts: 1,222
|
Re: hood hinge question
Thanks all for the tips, I'll hit the pivots with some oil and try it again...
So worn out springs would have nothing to do with this problem...???
__________________
'72 short step, 350, 700R4, tilt, ps, pdb, a/c, lowered coils, etc., other work in progress... San Diego, CA 72 Stepside Project |
![]() |
![]() |
![]() |
Bookmarks |
|
|