![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Apr 2011
Location: Philadelphia, PA
Posts: 173
|
low hanging exhaust???
Does this mid-section of the exhaust look like it's hanging too low? I don't know what's normal, but it looks a little exposed to me. The end of the exhaust is also right up against the bottom of the rear fender and angled slightly up. That doesn't look quite right either.
TIA.
__________________
1972 C-10 Deluxe 350 V8 - 350TH ------------------------------ We're not the jet set We're the old Chevrolet set |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: low hanging exhaust???
i've always just loosen things up and by pushin here and there and using good hanger system then retightened ,adjusted for alot better fit than that
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
![]() |
![]() |
![]() |
#3 |
72 GMC
Join Date: Feb 2008
Location: Wells, Maine
Posts: 534
|
Re: low hanging exhaust???
nice lookin' truck, though
|
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Apr 2011
Location: Philadelphia, PA
Posts: 173
|
Re: low hanging exhaust???
Thanks KEL.
I'm going to try fiddling with the hangers and see if I can get it raised up some.
__________________
1972 C-10 Deluxe 350 V8 - 350TH ------------------------------ We're not the jet set We're the old Chevrolet set |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Sep 2010
Location: Olympia, WA
Posts: 736
|
Re: low hanging exhaust???
Kinda looks like mine.....
|
![]() |
![]() |
![]() |
#6 |
Sisyphus was my mentor!
![]() Join Date: Sep 2002
Location: Carleton Place, Ontario CANADA
Posts: 984
|
Re: low hanging exhaust???
Saddly, they all look like that, & mine did too until last week when I did the typical conversion where you drill two 4" holes in the trailing-arm cross member, weld some tubing in there & route the exhaust through it.
__________________
passthebuck ![]() #5642 -TWO 1967 GMC 910's. One with L6/3-on-the tree and the other with 355 w/435hp & a 700r4. -a 2013 Honda Civic as my "sensible" car Last edited by passthebuck; 10-20-2011 at 01:43 AM. |
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: low hanging exhaust???
the people i've seen that put exhaust thru the crossmembers have also boxed them so as to strengthen them so that they dont fail// not just drilled big holes and weakened the crossmember
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Dec 2009
Location: Ste. Genevieve, MO
Posts: 526
|
Re: low hanging exhaust???
Mine is the exact same....nice truck!
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Jan 2009
Location: Rockmart, Ga
Posts: 27
|
Re: low hanging exhaust???
Here is the exhaust on my 69 gmc, the system is routed and tucked up between the frame rails and the body for a cleaner look from the side.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|