64-66 wiring harness in a 62

[LT1 Burb]

Has anyone tried converting a 64-6 wiring harness into their 62 or 63 truck. I have the most butchered up harness I have ever seen and have a box of good original 65 style to replace them with. I know the cluster will have to be altered but that's no big deal, figure I have nothing to lose.

[1963c-10]

Don't know personally, but I need a few of the accessory clips for the fuse box if you have any extras on an old fuse block. Both of the right side ones are missing on my fleetside.....I can get pics.

[pimpston65]

Originally Posted by 1963c-10

Don't know personally, but I need a few of the accessory clips for the fuse box if you have any extras on an old fuse block. Both of the right side ones are missing on my fleetside.....I can get pics.

you need the clips that are attached to the fuse box that hold the fuses? cuz i have a few extra fuses boxes

[1963c-10]

Originally Posted by pimpston65

you need the clips that are attached to the fuse box that hold the fuses? cuz i have a few extra fuses boxes

Yeah, its the clips on the right side. Got off late last night so wasn't able to get pics. I'll get some tonight.

[pimpston65]

Originally Posted by 1963c-10

Yeah, its the clips on the right side. Got off late last night so wasn't able to get pics. I'll get some tonight.

is this the clip u need?

[pimpston65]

hey LT1 this is the starter, coil,temp and oil sending unit i redid, correct terminal ends and heat sheild loom and correct colored wire and gauge, i follow'd the wiring diagram in the yellow book.

[61K10]

LT1Burb--should work with a few mods. I added a new aftermarket fuse block to my org harness. post up some pics 1963c-10.

[1963c-10]

Originally Posted by 61K10

LT1Burb--should work with a few mods. I added a new aftermarket fuse block to my org harness. post up some pics 1963c-10.

Will do, thanks. Bad part is I had a spare fuse box for parts a few months back, sent it to a member to help out on his project and then picked up the other 63.

[Bullett]

I just installed a new 14 circuit universal wiring harness/ fuse box in my truck, that was the best thing i could have done to my truck. i am going to do a frame off starting fall of 15' and will put a new painless wiring harness in at that point. But for $139, the universal harness is great. 2 full days to install but it sure is nice and neat.

[pimpston65]

Originally Posted by LT1 Burb

Has anyone tried converting a 64-6 wiring harness into their 62 or 63 truck. I have the most butchered up harness I have ever seen and have a box of good original 65 style to replace them with. I know the cluster will have to be altered but that's no big deal, figure I have nothing to lose.

hey LT1 if your in no rush, send the harness to me and i'll rewire it back to original.

[pimpston65]

Originally Posted by LT1 Burb

Has anyone tried converting a 64-6 wiring harness into their 62 or 63 truck. I have the most butchered up harness I have ever seen and have a box of good original 65 style to replace them with. I know the cluster will have to be altered but that's no big deal, figure I have nothing to lose.

i still have that 62 NOS fusebox if you need it...

[LT1 Burb]

Thanks Winston, let me pull this old harness out and I will snap some pictures of it, don't know if its save-able or not. What does the universal harness consist of Bullett.

[pimpston65]

Originally Posted by LT1 Burb

Thanks Winston, let me pull this old harness out and I will snap some pictures of it, don't know if its save-able or not. What does the universal harness consist of Bullett.

all i need is the connector ends and whatever you got, i just untape it,trace all the wires with new correct stuff. crimp,heat shrink the repaired ends with butt connectors and retape it all

[1963c-10]

Yes and at least the one under it also. With out looking at it I don't think there were any others. I can't remember if the bottom one was there or not. I'm inclined to think all three on the right side were gone. I will have to go over my harness with a fine tooth comb.....PO just tapped in all over the place.....bet I removed 20 different wires. Have the truck down to factory wiring only right now.

[pimpston65]

Originally Posted by 1963c-10

Yes and at least the one under it also. With out looking at it I don't think there were any others. I can't remember if the bottom one was there or not. I'm inclined to think all three on the right side were gone. I will have to go over my harness with a fine tooth comb.....PO just tapped in all over the place.....bet I removed 20 different wires. Have the truck down to factory wiring only right now.

let me know how many you need and i'll pull em out, i use the spare harness to fix the 65 and maybe the 66 burban if need be, to get em correct. its cheaper and easier to buy a junk harness and use the correct wire and terminal ends, then trying to find the wire, believe me i know!!! and the new wire has highly visable writing on it so it would'nt fly for those anal purest, like me hehe...

[1963c-10]

Originally Posted by pimpston65

let me know how many you need and i'll pull em out, i use the spare harness to fix the 65 and maybe the 66 burban if need be, to get em correct. its cheaper and easier to buy a junk harness and use the correct wire and terminal ends, then trying to find the wire, believe me i know!!! and the new wire has highly visable writing on it so it would'nt fly for those anal purest, like me hehe...

Ok, thank you. I'll have a total tonight. Let me know what I owe you for parts and shipping and I can have it out to you tomorrow!!

[1963c-10]

Nice job....looks great. Who did you order the loom from?

[pimpston65]

Originally Posted by 1963c-10

Nice job....looks great. Who did you order the loom from?

dude, it took me 4 stores and i finally found a electric store that only sales automotive stuff, and its local so i just walked in a picked the crap i needed

[1963c-10]

its the lower 3 outside pieces. the 2nd from the bottom has both pieces for the fuse, so it looks like all the lower 3 auxilliary ports are gone. i can get a pic up tomorrow...haven't masteres doing that off the phone yet.

[pimpston65]

Originally Posted by 1963c-10

its the lower 3 outside pieces. the 2nd from the bottom has both pieces for the fuse, so it looks like all the lower 3 auxilliary ports are gone. i can get a pic up tomorrow...haven't masteres doing that off the phone yet.

ok once i see the pic i will send it out, and i wont change ya.. just PM ur info

[1963c-10]

Here you go pimpston65. Auxilliary ports on the lower three right side

[66pnl]

The looming in post 13 is asphalt covered cloth loom available in several sizes at napa.

[pimpston65]

Originally Posted by 1963c-10

Here you go pimpston65. Auxilliary ports on the lower three right side

is this what you need?

[1963c-10]

Originally Posted by pimpston65

is this what you need?

Yes sir....those will work.

[pimpston65]

Originally Posted by 1963c-10

Yes sir....those will work.

cool, i got your info... i'll trade for those spiral shocks!!! just kidding. been sanding may days away so busy over the weekend, but i got banking to do friday and i ship em out... ps better clean um, not sure if patina is good for wiring!!!