looking for a 5x4.75 disc pattern - The 1947 - Present Chevrolet & GMC Truck Message Board Network

workinprogress67 · 07-30-2009, 07:28 PM

hi, i am looking for a 5x4.75 front disc bolt pattern for my 67 c10.i found a conversion kit from cpp and it says it will only work with stock spindles and i have 2.5" drop spindles. does anyone have or know of were i can find this pattern?

PBFAB.COM · 07-30-2009, 07:49 PM

Quote:

Originally Posted by workinprogress67

hi, i am looking for a 5x4.75 front disc bolt pattern for my 67 c10.i found a conversion kit from cpp and it says it will only work with stock spindles and i have 2.5" drop spindles. does anyone have or know of were i can find this pattern?

We have re-drilled the 5x5 rotors to 5x4.75 and then machined the nose cone down so the smaller bore car wheel would fit over it. Any machine shop should be able to handle the job. This might be the best option.

workinprogress67 · 07-30-2009, 09:12 PM

Are there any conversion kits? machine shops can get pricey.also my other question is, why does cpp say the 5x4.75 kit only works with stock spindles? drop spindles only lower the hub.

answer greatly appreciated

PBFAB.COM · 07-30-2009, 10:30 PM

Quote:

Originally Posted by workinprogress67

Are there any conversion kits? machine shops can get pricey.also my other question is, why does cpp say the 5x4.75 kit only works with stock spindles? drop spindles only lower the hub.

answer greatly appreciated

Not sure of any conversion kits that aren't complete (spindles/rotors/calipers).

Last time we redrilled the rotors and machined the nose-cone I only spent $50. It may be worth checking into.

BarryB · 07-30-2009, 09:35 PM

Theres a WIW thread over in the WIW section, a member removed his 5X4.75 disc frontend out from under his truck go check it out.

07-30-2009, 07:28 PM	#1
workinprogress67 Registered User Join Date: Jul 2009 Location: Millers, MD Posts: 36	looking for a 5x4.75 disc pattern hi, i am looking for a 5x4.75 front disc bolt pattern for my 67 c10.i found a conversion kit from cpp and it says it will only work with stock spindles and i have 2.5" drop spindles. does anyone have or know of were i can find this pattern?

07-30-2009, 09:12 PM	#3
workinprogress67 Registered User Join Date: Jul 2009 Location: Millers, MD Posts: 36	Re: looking for a 5x4.75 disc pattern Are there any conversion kits? machine shops can get pricey.also my other question is, why does cpp say the 5x4.75 kit only works with stock spindles? drop spindles only lower the hub. answer greatly appreciated

07-30-2009, 09:35 PM	#5
BarryB Senior Member Join Date: Jul 2006 Location: Blountville, Tn. Posts: 3,904	Re: looking for a 5x4.75 disc pattern Theres a WIW thread over in the WIW section, a member removed his 5X4.75 disc frontend out from under his truck go check it out. __________________ We could learn a lot from crayons... Some are sharp; some are pretty;and some are dull. Some have weird names; and all are different colours;but they all have to live in the same box. You may be only one person in the world, But you may also be the world to one person. * Some mistakes are too much fun to only make once. Two rules in life. 1. Never sweat the small stuff! 2. Everything is small stuff!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.