![]() |
|
![]() |
#1 |
Senior Member
Join Date: Aug 2002
Location: Valley Center KS
Posts: 3,525
|
![]()
Did anyone read about this monster in Hot Rod Magazine? I wondering how much this thing is going to cost. Might have to start saving now!
|
![]() |
![]() |
![]() |
#2 |
Almost Satisfied
![]() Join Date: Mar 2002
Location: Springfield, MO
Posts: 2,932
|
Ah, man I saw that beast. You can get it in one of two set ups. I think it was a 620 or a 720HP!! Incredible! I bet it will be in the range of $15K for that engine......
__________________
1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far." |
![]() |
![]() |
![]() |
#3 |
Half a bubble off!
Join Date: Jun 2000
Location: Winfield, Ks, USA
Posts: 5,588
|
We have visual contact:
__________________
Just call me LB. ![]() '71 Cheyenne, 402BB, hauls blondes, brunettes, or redheads. |
![]() |
![]() |
![]() |
#4 |
chevelito
Join Date: Jun 2001
Location: Honolulu, HI USA
Posts: 1,609
|
trucks! is installing it in their project copper head. damn that thing is bad @ss
__________________
New deadline...when my son can drive. ![]() Aloha from Honolulu, HI |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Jul 2002
Location: Champaign, IL
Posts: 1,397
|
That motor is bada$$. I don't want to see the pricetag. Isn't it supposed to be of limited quantity?
__________________
Baby Blue's Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=652776 Project 68's Build Thread: http://67-72chevytrucks.com/vboard/s...17#post8442117 www.stonecolumnclassics.com Email: Josh@stonecolumnclassics.com |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Aug 2002
Location: Crittenden, KY
Posts: 1,965
|
Lol. More visual contact. Yea, this thing is a beast. Though it may have some high horsepower, I think a well built small block could hang with it, What'd ya think?
Brandon |
![]() |
![]() |
![]() |
#7 |
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,403
|
Brabra......you dont mind if I chuckle a little about that well built sb keeping up with that big nasty RAT do you? My guess would be that the sb better have a BIG blower on it to play! Im runnin a sb, & love them, but have had a taste of BB power........lets just say "once bitten"..........
![]()
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Aug 2002
Location: Valley Center KS
Posts: 3,525
|
I think it's the ZL1 (aluminum 427) you're thinking of which is limit to 200 units.
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Aug 2002
Location: Crittenden, KY
Posts: 1,965
|
I mean to say built right a big block would prolly spank a small block. But if you took a small block and built it with the right compression, cam, and drivetrain, I just think it would run beside it. Small blocks are capable of making 4-5 hundred horsepower, and this one is what 602 or 672? Theres not that much of a difference. Also big blocks are notorious for torque, but not always necessarily horsepower, small blocks are opposite. I know this motor has huge horsepower ratings, but I just think built right, in the right application, say a Camaro, where weight of a car to weight of a truck would come into play, the underweight of the car should keep up with the big fat rat.
Sorry about the long post, kinda ran around in circles. Brandon |
![]() |
![]() |
![]() |
#10 |
Registered User
![]() Join Date: Aug 2001
Location: SOMERSET KY.
Posts: 6,427
|
![]() ![]() ![]() ![]() I GOTTA HAVE ONE OF THOSE 572s... I JUST GOTTA
__________________
junkyardjohn 69 1 TON TOW TRUCK // 84 4WD CUCV BLAZER// 85 1 TON 4WD STAKE TRUCK// 86 M1031 5/4 TON 4WD CUCV// ALOT OF OLD TRUCKS FOR ONE OLD MAN TO DRIVE. ![]() LIFE MEMBER OF P.E.T.A (PEOPLE EATING TASTY ANIMALS) DON'T RENT U-HAUL ALWAYS TELL THE TRUTH IT WILL AMAZE PART OF THE PEOPLE & ASTONISH THE REST Last edited by junkyardjohn; 12-16-2002 at 11:58 PM. |
![]() |
![]() |
![]() |
#11 |
Senior Member
Join Date: Dec 2001
Location: Redding,CA...USA
Posts: 4,736
|
the aluminum headed big block weighs 100lbs more than a small block, that adds a tenth to the time of the quarter. To reach 650 hp, the max torque would be in the 5,500 rpm range and max HP will be at around 6500...plus it should have 400+ torque from 2000 on...for a small block to reach 500HP it would have the same rpm range, except the torque would not be there until it reaches 4000rpm...lol..now im rambling..ANYWAYS the big block will smoke a small block
__________________
It's called "drag racing" if they called it "tic..tic..WHAM!..BANG! F*&K!!!", they'd have to keep the magazines under the counter with the other men's publications click the clicky to join the site.... http://67-72chevytrucks.com/vboard/payments.php 67 lwb..first hotrod in 25 years..540 best ET is 9.45 @ 141.44 Anderson,CA |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Aug 2002
Location: Crittenden, KY
Posts: 1,965
|
Oh, I guess I'll just shut up. I guess I don't know what any real high horsepower engines run. I'm around beefed up cars at drags and crap, but never a 650 horse beast. Guess just thought since it was so big I guess it's kinda like the big and awkward thought. Pretty much anyone I know that runs worth a shiznit runs a small block. I don't really know the nature of the beast, just thought incorrectly. Sorry. I'm thinking I know more than I do. I am 15 ya know, we tend to do that.
Brandon |
![]() |
![]() |
![]() |
#13 |
Registered User
![]() Join Date: Dec 2001
Location: Pace, FL
Posts: 2,155
|
Probably all your friends would run that beast if they were rich dudes- but in perspective, not many people have the $$$ to buy one of those beasts. Wonder how that would fit into my truck?
__________________
1942 Master Deluxe 1969 C/10 1985 Blazer CUCV 1987 Jimmy 2004 Tahoe 2005 Silverado 1500 2005 Silverado 3500 |
![]() |
![]() |
![]() |
#14 |
Livin' it up.
![]() Join Date: Nov 2001
Location: Richland, MI
Posts: 2,212
|
Brabra... a SB could keep up with that beast (in stock form) but it'd be built like a brick sh!thouse and would be a costly toy... the power and torque you get outa a BB is diff than a SB.
most people run built SB's because well its DAMN cheap... (comparatively speaking) versus building a BB.. with so many distrubutors of quality and bad arse parts for the 350 it's not tough to build em up stron and cheap.. a BB however with some nice mods (ie full roller valvetrain) can really wake up and still have a great usable band, specially for our trucks, whereas a really stout SB will have a lesser streetable quality... now what i wanna see with that Bad Boy is some specs cuz i dont know any on it other than bore and stroke... (is it all forged? i'd hope so) if so then slap some dish pistons in, and break out the turbos off a nice MAC truck.. that'd be one NASTY rat... muhahah ok i'm done now ehhe
__________________
-Greg; Sold the 69 C20. It's off to a better home with more love! Now onto the 86 CUCV M1009; K5 blazer with 6.2L diesel, corp 10 bolt axles, Detroit locker in the rear, trutrac front, 3.73 gears, 35" tires. ![]() |
![]() |
![]() |
![]() |
#15 |
14.1 @ 96MPH
Join Date: Jul 2001
Location: Mesa, AZ
Posts: 2,811
|
__________________
Project1970 - LS1 Swap Complete! ![]() |
![]() |
![]() |
![]() |
#16 |
Boosted Member
Join Date: May 2002
Location: Mackinaw, IL
Posts: 2,200
|
Ok, well that page is filed under "wet dream" in my favorites section......at least until it gets a price. Then it goes to "drool and dream"
__________________
1972 2wd K/5 Blazer Turbocharged 370 LSx - 941 rwhp / 1093 rwtq 1969 Chevy K-10 L33 5.3 / 4L80E / NP241 / 4" lift 1964 Buick Skylark Twin TURBO 383 LS pro-touring project 2014 VW Passat TDI - Daily Driver Turbo diesel 2015 Sierra Denali HD Duramax Turbo diesel 2016 Ford Explorer Sport - Twin Turbskis 2017 Polaris RZR Turbo 2014 Nor-Tech Center Console - Twin Supercharged Outboards TURBO ALL THE THINGS!! |
![]() |
![]() |
![]() |
#17 |
Registered User
Join Date: Aug 2002
Location: Iowa
Posts: 119
|
![]()
That motor is WAY mild. I know it sounds like the cam and carb are big, high HP pieces, but on an engine that large, its barely adequate (defnitely needs a bigger carb). Not to mention the 9.6-1 compression. Id bet that engine would be livable day to day, if you could pony up the fuel dollars...
A 600 plus HP, normally aspirated small block, OTOH, would be very radical, nearly unstreetable. It could be done, with blowers,turbos, or big nitrous, but a Rat motor with that kind of hardware can easily be a 1000 HP piece. Further, when you start talking major HP (600+) the cost advantages of the small block start to disappear, as the economies of scale, start to diminish. For instance, a Scott Shafiroff Racing Egines, 434 makes 675 hp, and costs $11,250, while a 540 makes 835 hp, for the same money... Fix the heads, and a big block Chevy, is a damn impressive engine. -Marty '72 Blazer, 396/350, mildly built, 4spd, 3/4 ton axles (soon), 36 Swamper Radials (yech) PS: Reher & Morrison, Shafiroff, Bill Mitchell, and other sell big inch 'crate motors' for probably the same money as this thing will cost...eg. Shafiroof's 572 is $12,500 and belts out 875 ponies. |
![]() |
![]() |
![]() |
#18 |
Registered User
Join Date: Feb 2002
Location: Richmond MO,USA
Posts: 73
|
Pacific Performance has a 585hp 502 fuel injected crate motor for around $6k.
__________________
72' Camper Special,454,th350,np205,4.56 locker,dana44 with spool,13" of lift and 44" boggers.soon to be 23" with rear disc brakes |
![]() |
![]() |
![]() |
#19 |
Account Suspended
![]() Join Date: Oct 2002
Location: NC
Posts: 1,129
|
cubic inches
There is no replacment for displacement!"cubic inches"But per dollar spent a 400 small block is a bad mouse.I have about $2500.00 in a 400 that I assembled with good parts , forged pistons ,arp bolts,comp cams valve train 186 LT1 heads 750 holley etc. Motor is in 69 swb GMC set back in 6 cylineder postion ,no power anything .1 belt for alt and water pump .Has electric fans.308 posi th350 with 24oo converter.Truck will chirp drive at 100 mph plus , hold you back in the seat and take you for the ride of your life!!!! I had 454 in the same truck with the same trans and gears .It was faster in the quater but I could make the 30 mile trip home on the back roads alot faster with the small block. With small block in 6 cyl postion and loprofile tires truck would take curves 20to30 mph faster.So unless you want to dragrace or just bragg about I think the mouse beats the rat.I think I'll spend my other $12,500 on a nice truck to put it in.
|
![]() |
![]() |
![]() |
#20 |
I am a Referee of life.
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,993
|
WHEN! ,they get around to offering this thing in a short block it will really take off.I think with some aluminum heads, a decent intake and the right cam, you could probably get close to 700 "streetable" hp out of it.With aluminum heads and the right cam combo you could probably run it around 10.5 comp.ratio.Use a 2500 converter and built 350 and drop it in a S10 and you would have a sure fire street beast if you could get it to hook up.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" |
![]() |
![]() |
![]() |
#21 |
GMC SHORT FLEET F/S
Join Date: Jun 2000
Location: SOUTH WILLIAMSPORT PENNSYLVANNIA
Posts: 2,117
|
some will soon photo shop it into their truck!
__________________
CHARLES WADE HEIN HVACR FOREMAN. LEWISBURG U.S.P. |
![]() |
![]() |
![]() |
#22 |
Registered User
![]() Join Date: Feb 2001
Location: East Central, MO
Posts: 11,336
|
I'd like to drop it into my truck.
![]() |
![]() |
![]() |
![]() |
#23 |
Senior Member
![]() Join Date: Oct 2001
Location: Edgerton OH USA
Posts: 631
|
This engine will be offered in 2 versions. A 9.6:1 pump gas engine with 620 horsepower and a 11:1 720 hp version with the dominator carb. I would be suprised if the 620hp was priced too much higher than the Ram Jet 502. Still a lot of money but affordable as far as crate motors go.
Tom
__________________
'69 swb stepside in progress. '59 Corvette lifetime project |
![]() |
![]() |
![]() |
Bookmarks |
|
|