The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > Info Center > FAQ Truck Tech > 60-66

Web 67-72chevytrucks.com


Closed Thread
 
Thread Tools Display Modes
Old 12-23-2011, 06:42 PM   #1
Woogeroo
Registered User
 
Join Date: Aug 2003
Location: tool box
Posts: 3,115
Wink Re: dome light assembly : how to remove and replace?

To read the original thread and discussion on this topic go here- LINK


photo one : dome light assembly hole with old wires



photo two : top of the fuel tank, behind the driver side of the cab, shows the white and orange/white wires running down the two clips back there. On my truck the wires ran down there, then under the door sill/plate thing with the chevy logo on it. From there it ran up past the bright lights on/off switch to the fuse panel where the plug snaps in.



photo three : bad dark rainy day photo showing the wires running by the dimmer switch



photo four : dark shot of the plug and the fuse panel.



My biggest aggravation with this project was getting the sill loose as all of the phillips heads stripped out on me. If your truck is beat up and rusty like mine, I would suggest working on getting that part loose before tackling the rest of the project.

-W

Last edited by augie; 05-09-2012 at 02:06 AM.
Woogeroo is offline  
Old 12-23-2011, 06:44 PM   #2
Woogeroo
Registered User
 
Join Date: Aug 2003
Location: tool box
Posts: 3,115
Wink Re: dome light assembly : how to remove and replace?

photos five, six, seven, shows where the wire was running under that plate.

I used to know what that plate was called...

-W
Attached Images
   
Woogeroo is offline  
Old 12-23-2011, 06:48 PM   #3
Woogeroo
Registered User
 
Join Date: Aug 2003
Location: tool box
Posts: 3,115
Thumbs up Re: dome light assembly : how to remove and replace?

The finished installation in the daytime.

The reproduction dome light assembly and the clear lens are both from LMC truck. I was very happy with the parts, which is not something I can always write about with LMC parts.

The reproduction dome light assembly has plastic snaps on the back that line up with the screw holes in the cab. You could drill a hole in it, if you wanted to I suppose, but I just snapped mine in.

I also bought the clear lens at the same time. It really puts out a lot more light, even with the standard bulb.

Oh yes... the dome light assembly came with the opaque cover and a bulb already in it. Just in case anyone wonders.

I never could get the plug to fish through the cab... I was cold, wet and rather mad, so I just cut the wire, fished it through, spliced it and went on with my day.

Thanks to everyone for their suggestions.



-W
Attached Images
 
Woogeroo is offline  
Old 12-25-2011, 07:31 PM   #4
Woogeroo
Registered User
 
Join Date: Aug 2003
Location: tool box
Posts: 3,115
Re: dome light assembly : how to remove and replace?

a little tech article I wrote using the photos I took while doing this project.

dome light assembly - remove and replace.


-W

Last edited by N2TRUX; 12-04-2012 at 11:39 AM.
Woogeroo is offline  
Closed Thread

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:47 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com