![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Oct 2002
Location: The Netherlands
Posts: 118
|
wheel studs-please help
Last week I installed a rear discbrake conversion kit from SSBrakes.
Everything fits and works like a charm, BUT: now the wheelstuds are too short too fit the wheelnuts more than 3/4. Doesn't look very safe to me. ![]() I need longer studs, but don't know wich ones. Does anybody here know what the sizes are? Threadsize, knurl head size, knurl diameter end length? I tried Summit, Moroso, Arp, etc, but can't find the specs for 1984 Chevy C10 studs. I'm living in Europe, so I'm unable to find studs here in local autopart shops. Please help, this car is my daily driver, and I'm not feeling very comfortable now, afraid a wheel comes off.
__________________
*Andre* 1984 C10 SWB, 350/700R4 ![]() |
![]() |
![]() |
![]() |
#2 | ||
just can't cover up my redneck
Join Date: May 2004
Location: Columbus OH
Posts: 11,414
|
Re: wheel studs-please help
Quote:
As long as the threads go completely thru the nut you are ok, you don't need any extra.
__________________
You can review the site's rules here. Quote:
Bad planning on your part does not necessarily constitute an instant emergency on my part.... The great thing about being a pessimist is that you are either pleasantly surprised or right. ![]() |
||
![]() |
![]() |
![]() |
#3 |
BMW & ASE Master Certified
Join Date: Feb 2004
Location: Houston, Texas
Posts: 1,262
|
Re: wheel studs-please help
this is factory size
dorman pt # 610-138 Thread Knurl Dia. Length Shoulder 1/2"-20 .535" 1-17/32" 5/16" and this is what I used: dorman pt# 610-298 Thread Knurl Dia. Length Shoulder 1/2"-20 .547" 2" 11/16" For me, it worked perfectly, as I was in the same boat too. I bought a speical drill bit to open the hole just a bit.. but I wasted my money. It didnt make that big of a difference becuase a BFH pressed them in w/o using the bit on the other axle. good luck
__________________
1987 Silverado - L83 5.3 w/ 6L80e ,A/C,P/W,P/L,TILT, HID projectors, Wilwood C-10 Pro Spindles w/ 2018 silverado front brakes & C-5 Corvette Rear Disc Brakes 1999 BMW 528i - 5.7 LS1 w/ 4l60e, Ford 8.8 IRS w31 spline posi & FX-r projector retrofit New project: 2006 BMW x5 6cyl AWD to L83 6l80e 4wd to 2WD / RWD A poor man buy's it twice finally got my domain name back, 87chevy.com.... site rework in progress |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Oct 2002
Location: The Netherlands
Posts: 118
|
Re: wheel studs-please help
Thank you very, very much. I'm gonna order them immediately.
@LONGHAIR: I meant 3/4 of the nut ![]() This is a great board ! ![]()
__________________
*Andre* 1984 C10 SWB, 350/700R4 ![]() |
![]() |
![]() |
![]() |
Bookmarks |
|
|