|
|
|
06-08-2004, 03:19 AM
|
#1 |
|
Oilfield Trash
Join Date: Sep 2003
Location: Raymore, Sk, Canada, Earth
Posts: 3,170
|
Tranny Question
is it possible to swap a muscle car style 4speed(like a t10) into a 71? the other cab i am using is a setup for a manual.
__________________
14 Dodge 3500 Mega Cab 08 Dodge 3500 Mega Cab 87 Chev 3+3 4x4 80 GMC K10 High Sierra bone stock 70 Chevelle 350SS long term project 68 GMC 3ton Grain Truck/Garbage wagon 50 Pontiac 2 Door Coupe Project "I've got a shotgun rifle and a 4 wheel drive and a country boy can survive" Hank Jr. |
|
|
|
06-08-2004, 09:05 AM
|
#2 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
yes you can
 I ran an M21 muncie in my 71 (pretty easy swap). Remember that some of the hypo car trannies had a 1 1/8 x 26 spline input shaft, vs 1 1/8 x 10 spline on the truck trans. the centerhole on the bell is also a diff size for the car(4.683, vs 5.126 on the truck). If you use a 67 or older truck bell, you will have the proper bell to swap the car trans in. im not sure on the lenght/spline on the T -10, but the muncie (M 20/21) will bolt right in where a saginaw 3 spd came out (no driveline mods). best of luck,crazyL 
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
06-10-2004, 01:34 AM
|
#3 |
|
Oilfield Trash
Join Date: Sep 2003
Location: Raymore, Sk, Canada, Earth
Posts: 3,170
|
what kind of shifter did u use?
__________________
14 Dodge 3500 Mega Cab 08 Dodge 3500 Mega Cab 87 Chev 3+3 4x4 80 GMC K10 High Sierra bone stock 70 Chevelle 350SS long term project 68 GMC 3ton Grain Truck/Garbage wagon 50 Pontiac 2 Door Coupe Project "I've got a shotgun rifle and a 4 wheel drive and a country boy can survive" Hank Jr. |
|
|
|
|
06-10-2004, 08:41 AM
|
#4 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
I used a Hurst . the indy, super speedway, or the competion plus should work. the indy & the superspeedway were a more universal fit, & mount the shifter fairly high on the trans (not a problem in the truck). If you have a bench seat, you may have to modify the handle, or build your own to clear the seat(the handle bolts off with 2 bolts). of the 3 listed, the comp plus is the best quality. you could probably run a Ramrod (vertical gate), but would have to "butcher" the floor pretty good to fit it. Best of luck,crazyL
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
