|
|
|
06-11-2004, 05:09 PM
|
#1 |
|
Senior Member
 Join Date: Feb 2001
Location: Austin, Texas, USA
Posts: 1,628
|
Bed Floor Question??
Hi all.
Can anybody tell me if the corrugated steel floor in our trucks is the same as the corrugated steel floors in the 73+ trucks. The very rear edge of my Blazer has a couple of rust out areas about the size of a quarter. I was wondering if I could use the rear edge of a 73+ truck as a donor. There is only one decent 69-72 pickup around here in the yards and the bed on it is not too bad. It would be a sad waste to cut it for patch panels. There are tons of 73+ trucks around and the pattern in the floor and across the very rear edge looks to be the same. Wasn't able to do a side by side comparison. Thanks.
__________________
'72 Chevy Blazer |
|
|
|
06-11-2004, 05:20 PM
|
#2 |
|
RUNN over AGAIN!!!
Join Date: Jun 2003
Location: Big Spring, Texas
Posts: 505
|
Id like to know too.
__________________
67-72 TRUCKS ROCK 70 SWB shaved and a 72 front clip.and a poly tank. Peep mirrors and a BIG BLOCK 468 in the making. XNXNXNXNXNXNXNXNXNXNX ,/. EMAIL ME HERE!, Dont pm me please ,/. |
|
|
|
|
06-11-2004, 06:23 PM
|
#3 |
|
Account Suspended
Join Date: Sep 2000
Posts: 3,991
|
They are different. I would snatch up any good floor you can find. The also sell patch panels, they are 16x48"
|
|
|
|
|
06-11-2004, 06:26 PM
|
#4 |
|
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,468
|
ANYONE WHO LIVES IN OUR SOLAR SYSTEM HAS GOT TO BE CORRECT. :p
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
|
|
|
06-11-2004, 07:56 PM
|
#5 |
|
Senior Member
Join Date: Feb 2001
Location: Austin, Texas, USA
Posts: 1,628
|
Thanks Gee Emm. I haven't seen any patch panels with the finished ends at the rear of the bed. Do they make those?
__________________
'72 Chevy Blazer |
|
|
|
|
06-11-2004, 08:26 PM
|
#6 |
|
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,468
|
HUSKER, U MIGHT BE ABLE TO BUY A BLAZER TAIL PAN FROM LMC FOR $29.95
AND INCORPORATE IT INTO YOUR REPAIRS, JUST A THOUGHT. ( PAGE 33 )
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
|
|
|
06-12-2004, 02:21 AM
|
#7 |
|
Senior Member
Join Date: Feb 2001
Location: Austin, Texas, USA
Posts: 1,628
|
I thought about that, but the only problem is, I have a '72. The tailpan is different on the '72. There are two cutouts that go around where the frame comes out of the back. On 69-71, they are straight across, no cutouts. The ones in LMC are 69-71 type.
__________________
'72 Chevy Blazer |
|
|
|
|
06-12-2004, 09:04 AM
|
#8 |
|
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,468
|
Ah, I C. It Was Worth A Thought.
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
|
|
|
06-12-2004, 11:41 AM
|
#9 |
|
Account Suspended
Join Date: Sep 2000
Posts: 3,991
|
The floor can be removed from the rear cross sill, they are two different pieces. Not sure what this piece in LMC looks like, is it part of the floor or a replacement cross sill?
|
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
