![]() |
|
![]() |
#1 |
Registered User
![]() Join Date: Dec 1999
Location: Modesto, CA
Posts: 565
|
changing body mounts?
are your body mount bolts welded to your body as well? if so how do we switch out the bushings without completely lifting the body?
__________________
Current owner of 2016 2500 Silverado Midnight Edition. Former owner of: 69 1/2 ton, change from long/fleet to short/fleet, shaved door handles, shaved tailgate, 4/6 drop, power windows, 700r4 72 blazer, 350 with Holley Commander 950 DFI, crane energizer cam, 350 tranny, dual sanderson blockhuggers/magnaflow exhaust |
![]() |
![]() |
![]() |
#2 |
PROJECT 7DEUCE
![]() Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,608
|
Your body bolt's should not be welded to the body if so I would cut off the head of the bolt and replace the bolt's when you replace the bushing's..
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jan 2002
Location: Canton, Georgia, USA
Posts: 1,119
|
Finally something I can comment on. I just finished replacing the body mounts in my 72. Yes each bolt has a spot weld to help secure the bolt. I took a cut-off wheel and cut the heads like pizza and used a cold chisel to break them off. The ones in the floorboards are sunken (sp?) in recessess. I used a cut-off wheel and tried to make a cross that went through the middle, and then used a large drill bit to drill the head of the bolt off. I ended up having to use the chisel to finish the break of the head. I used a grinding stone on the end of a die grinder to clean off the spot weld.
I did one side at a time. I used a floor jack and some pieces of 2 x 6 (to spread the weight) and lifted each side of the body. It really wasn't that bad of a job. I got the mount kit from Tim Christian and it was perfect. I would suggest getting a very good quality drill bit for the bolts going through the floorboard.
__________________
Jeremy (NUBOMB) 72K5 CST 350/350/205 1951 Chevy 1/2 ton North Georgia Group "... And the first rule to being a man is you gotta spend your life doing crap you don't wanna do." Red Forman. |
![]() |
![]() |
![]() |
#4 |
Senior Member
![]() Join Date: Feb 2001
Location: Austin, Texas, USA
Posts: 1,628
|
Yes, the body bolt heads are tack welded to the floor from the factory. You can grind them, although the recessed ones can be tough to get at with a grinder.
__________________
'72 Chevy Blazer |
![]() |
![]() |
![]() |
#5 |
Senior Member
![]() Join Date: Feb 2001
Location: Austin, Texas, USA
Posts: 1,628
|
You beat me to it NuBomb.
__________________
'72 Chevy Blazer |
![]() |
![]() |
![]() |
#6 |
Registered User
![]() Join Date: Dec 1999
Location: Modesto, CA
Posts: 565
|
and this is definitely easier than lifting the body, what would it be, 8 inches? right? you should know that i just put in the engine and tranny and havent put the fenders back on yet
I appreciate the input
__________________
Current owner of 2016 2500 Silverado Midnight Edition. Former owner of: 69 1/2 ton, change from long/fleet to short/fleet, shaved door handles, shaved tailgate, 4/6 drop, power windows, 700r4 72 blazer, 350 with Holley Commander 950 DFI, crane energizer cam, 350 tranny, dual sanderson blockhuggers/magnaflow exhaust |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Sep 2003
Location: Evergreen, CO
Posts: 494
|
Mine were tack welded to the floor too. I just center punched the bolt heads and drilled through them... used a 1/4" punch to drive the bolts down through the mounts and an air chisel to knock the heads off.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|