massive creaking sounds from front end - The 1947 - Present Chevrolet & GMC Truck Message Board Network

plumbcut · 08-27-2004, 07:32 PM

A couple years ago I rebuilt a 4x4 pickup completely, from the ground up. The front end now creaks hellaciously whilst turning the steering wheel left to right (and back), especially at slow speeds like pulling into or out of a tight parking space.

Anyone ever experience something like this? The frame was powder coated and Im thinking its the rivets creaking where they have started to (surface) rust... I dont really want to bathe my truck in wd40 to see if its the culprit. The frame is pristine (no steering box cracks), has an AGR steering box, urethane body/spring/motor/swaybar/etc mounts EVERYWHERE, a steering box brace, the steering box has grade 8 studs that are TIGHT.

There is about 4 inches of lift, with the appropriate dropped steering arm. The front axle knuckles have new Dana ball joints upper & lower, and new tie rod ends everywhere.

If I sit under the front end while someone turns it, it doesnt really seem to come from a specific location, just sort of everywhere. Any advice? The truck started doing this a few months ago (not driven very often).. Maybe I will take a video w/ good sound of the truck.. My truck drives along the road *****in, and sounds like a tight truck. No squeaks, rattles, etc, until I make a tight slow turn and it creakkkks..... There sure is a lot of flex in the front end & frame on this old pickup, especially for having just medium sized tires and lift (4" and 33's)....

plumbcut

*1FaastC10* · 08-27-2004, 07:59 PM

Quote:

Originally Posted by plumbcut

urethane body/spring/motor/swaybar/etc mounts EVERYWHERE

i think you just answered your own question.

**N2TRUX** · 08-28-2004, 10:55 PM

Originally Posted by plumbcut
urethane body/spring/motor/swaybar/etc mounts EVERYWHERE

Quote:

Originally Posted by 1FaastC10

i think you just answered your own question.

That was my thought too. PC do you think it the dreaded urethane bushing groan? They can make some pretty nasty noise. I learned that a long time ago on a lift kit with those pretty yellow bushing. I had no idea they would require a half a can of WD-40 after every off road adventure....

C&C Chevy · 08-27-2004, 09:19 PM

Check to see if the rotors are loose. I put new ones on mine and it developed the same sounds as yours. After rechecking them, it turned out the pass. side rotor was loose. I put it back on a notch tighter on the castle nut.

plumbcut · 08-28-2004, 03:34 AM

Quote:

Originally Posted by C&C Chevy

Check to see if the rotors are loose. I put new ones on mine and it developed the same sounds as yours. After rechecking them, it turned out the pass. side rotor was loose. I put it back on a notch tighter on the castle nut.

now thats a thought. Seems like a longshot, but Ill definately check it out.

as far as it being bushings or the pump, its definately neither of them. Its a stress creak sound, like the sound that you get when you walk on an old wooden subfloor...

pc

Skull Bucket · 02-13-2019, 12:12 AM

Quote:

Originally Posted by C&C Chevy

Check to see if the rotors are loose. I put new ones on mine and it developed the same sounds as yours. After rechecking them, it turned out the pass. side rotor was loose. I put it back on a notch tighter on the castle nut.

C&C Chevy - thanks for sharing !! I been going nuts over the same issue and after I read your post I went and checked my front wheels and sure enough just the slightest play was present...I had opted for a tad on the loose side so as not to put excessive pressure on the bearings....but turns out that one notch "loose" on the castle nut was just enough to be the difference between a quiet wheel and a creaking wheel!

cliffsta · 08-27-2004, 11:53 PM

hmmm, maybe power steering pump? My mom's 98 ford windstar's power steering pump SCREAMS when you turn at slow speeds, IE when the power steering is utilized the most. A whailing power steering pump usually starts out quiet and progressivly gets worse until it s all you here. Just a thought. If you ever replaced it with anything but OE then it won't take long for it to start screaming. My 80 C10 has the original power steering pump and I'm praying it lasts since from what i hear replacements suck. Hope that helps.

*1FaastC10* · 08-28-2004, 05:06 PM

when was the last time you greased your chassis?

08-27-2004, 07:32 PM	#1
plumbcut california fill Join Date: Apr 2004 Location: Sunny So-Cal Posts: 694	massive creaking sounds from front end A couple years ago I rebuilt a 4x4 pickup completely, from the ground up. The front end now creaks hellaciously whilst turning the steering wheel left to right (and back), especially at slow speeds like pulling into or out of a tight parking space. Anyone ever experience something like this? The frame was powder coated and Im thinking its the rivets creaking where they have started to (surface) rust... I dont really want to bathe my truck in wd40 to see if its the culprit. The frame is pristine (no steering box cracks), has an AGR steering box, urethane body/spring/motor/swaybar/etc mounts EVERYWHERE, a steering box brace, the steering box has grade 8 studs that are TIGHT. There is about 4 inches of lift, with the appropriate dropped steering arm. The front axle knuckles have new Dana ball joints upper & lower, and new tie rod ends everywhere. If I sit under the front end while someone turns it, it doesnt really seem to come from a specific location, just sort of everywhere. Any advice? The truck started doing this a few months ago (not driven very often).. Maybe I will take a video w/ good sound of the truck.. My truck drives along the road *****in, and sounds like a tight truck. No squeaks, rattles, etc, until I make a tight slow turn and it creakkkks..... There sure is a lot of flex in the front end & frame on this old pickup, especially for having just medium sized tires and lift (4" and 33's).... plumbcut

08-27-2004, 09:19 PM	#4
C&C Chevy Registered User Join Date: Feb 2003 Location: Midwest City, OK Posts: 1,001	Check to see if the rotors are loose. I put new ones on mine and it developed the same sounds as yours. After rechecking them, it turned out the pass. side rotor was loose. I put it back on a notch tighter on the castle nut. __________________ Robert Current: 1986 SWB Silverado 4.3 / TH400 Past: 1985 SWB Silverado 305 / TH350 - sold 1995 1987 1/2 ton Silverado - FI 350 / 700R4 sold 2007

08-27-2004, 11:53 PM	#7
cliffsta Stepsides RULE Join Date: Jul 2004 Location: Pineville, LA Posts: 1,921	hmmm, maybe power steering pump? My mom's 98 ford windstar's power steering pump SCREAMS when you turn at slow speeds, IE when the power steering is utilized the most. A whailing power steering pump usually starts out quiet and progressivly gets worse until it s all you here. Just a thought. If you ever replaced it with anything but OE then it won't take long for it to start screaming. My 80 C10 has the original power steering pump and I'm praying it lasts since from what i hear replacements suck. Hope that helps. __________________ 1981 Chevy C10 Custom Deluxe Stepside 350 V8, headers, side exhausts, 3-speed auto SOLD 1980 Chevy C10 Custum Deluxe Stepside 305 V8, Edelbrock Performer Intake, Edelbrock 1406 600CFM 4-barrel, TH350C. Bent rod. SOLD 1984 GMC Sierra Classic Longbed 6.2L Diesel SOLD 2009 Kawasaki KLX-250S too many mods for this signature 1999 Honda Accord EX 4-cylinder, 17" Motegi Wheels 215/45/17 Sumitomo tires, Tein S-Tech lowering springs, KYB GR2 shocks, Acura TL 20mm rear swaybar, debadged, blackhoused headlights, Short-Ram Intake Cardomain of the Accord

08-28-2004, 05:06 PM	#8
1FaastC10 Account Suspended Join Date: Oct 2002 Location: Elkhart, IN Posts: 6,399	when was the last time you greased your chassis?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.