|
|
|
09-04-2004, 10:54 AM
|
#1 |
|
Registered User
Join Date: Aug 2004
Location: Raleigh, NC
Posts: 36
|
Removing Ball Joints
Can I grind the rivots off to remove the ball joints on the control arms since i will be replacing them?
__________________
67 GMC LB (all in parts for now) |
|
|
|
09-04-2004, 12:20 PM
|
#2 |
|
Registered User
Join Date: Nov 2003
Location: Alexandria, VA
Posts: 1,534
|
Grind off, drill off or chisel them off and drive them out with a pin punch.
__________________
'72 GMC SWB C1500 Custom, frame-off in progress. 383 SBC, 9:1CR, Comp Cams XE262H, Scat internal balanced crank, Eagle SIR 6" rods, Keith Black dish pistons, Dart Iron Eagle 72/180 heads, Weiand Stealth intake, Stewart stage I water pump, Holley 4bbl vac sec, TH350 with B&M Shift Improver Kit. 12 bolt positraction.   
|
|
|
|
|
09-04-2004, 01:30 PM
|
#3 |
|
A-Adam A-Adam
Join Date: Apr 2003
Location: Sarpy Co. Ne. South of Omaha
Posts: 263
|
Just did my uppers. Drill a 1/4 in hole in them and the hit them with a good sharp chisel. The head will pop off then drive the rest of the rivot out with a punch
__________________
70 3/4 ton GMC Camper Special |
|
|
|
|
09-04-2004, 05:30 PM
|
#4 |
|
Registered User
Join Date: Aug 2004
Location: Raleigh, NC
Posts: 36
|
Uppers were easy, any help with the lowers?
__________________
67 GMC LB (all in parts for now) |
|
|
|
|
09-04-2004, 07:09 PM
|
#5 |
|
Registered User
Join Date: Feb 2002
Location: Vacaville, CA
Posts: 2,745
|
I use a press but you can rent a tool for free from AZ that will remove and install.
__________________
 70 C/10 Light Red 350/TH350, HEI, Duals w/40 series Flows, 91 seat, LED taillights 99 Pontiac S/C GTP, SLP Ram Air hood, GMPP Konis & springs 95 Neon ACR, MP PCM, AFX UDP, 3.0 CAI |
|
|
|
|
09-04-2004, 11:53 PM
|
#6 |
|
Navel Inspector
Join Date: Mar 2003
Location: Wichita, Ks
Posts: 1,373
|
I want to make sure. AZ = Auto Zone?
__________________
1948 Chevy Aerosedan GONE! I think. 1984 Cadillac Fleetwood Brougham Coupe WANTED 1967 IMPALA 1967 CST C10 Long Bed with a 283 |
|
|
|
|
09-05-2004, 01:55 AM
|
#7 | |
|
Insert funny comment.
 
Join Date: Dec 1999
Location: Concord NC
Posts: 621
|
Quote:
__________________
------------ - Mark -My Build Thread... -68 C10, LT1 - Undergoing Frame off resto -86 IROC-Z T72 turbo 355, M6 -70 Camaro http://www.iroc-ss.com |
|
|
|
|
|
09-05-2004, 02:56 AM
|
#8 |
|
Saving 1 truck at a time!
Join Date: Aug 2001
Location: Kent, WA
Posts: 6,465
|
The lower ball joint requires a press to get it out of the lower arm and a press to put the new one back in place. Unless you have access to one you are going to have to get an auto machine shop to help you.
__________________
'68 C20 Longhorn 50th Anniversary 400/TH400 '68 C20 Longhorn 50th Anniversary 468/TH400w/buckets '72 C20 Halfhorn (Longhorn w/o cab and front clip) '69 Flxible Cruiser (look up ugly in the dictionary) |
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
