69 SWB GMC for sale - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Longhorn Man · 10-31-2004, 06:27 PM

Selling my short/fleet GMC (chevy front clip)
It does run, but knocks like crazy once warmed up. The TH350 bolted up to it was rebuilt in 97 and has maybe 30K on it sence then. Never slipped once, fluid been chainged every year...is leaking a little though. B&M 1900 RPM converter.
once piece drive shaft.
Hooker comp headers.
coil spring rearw/3.07 gears.
Van tilt installed w/later 4 spoke GM wheel.
edelbrock performer intake
edelbrock 750/manual choke carb
manual drum brakes in need of help
big block engine towers. (dunno why, onless they were also V-6 towers)

Buy it, slap a motor in it, do some brake work and have a fun daily driver/beater.

If you want a truck to restore, this one needs lots of work. Most body panels almost look good at first sight, and look worse up close.

Come and get it in columbus ohio, need a trailer or tow bar. Even though I can fire it up and move it, the headers are open and I'm selling it as not driveable. I might be able to deliver a short distance...100 miles or less.

$650 as it sits, add 100 bucks and you can have the tow bar, tail light harness and safety chain.

I'll get pics soon hopefully.

Please answer w/questions, comments, pic requests...ect, on this thread, not in my PM box or e-mail. You'll get a quicker responce here anyways.
Payable w/cash,money order,postal money order...can store here for a short period of time, not very long though. It is dead and parked on the street.

Longhorn Man · 10-31-2004, 06:29 PM

Oh yea....home done LED tail lights and a very pretty engine with some cheap (but nice) chrome...if any of that is important.
power steering
Int reg alt
HEI
new-ish starter and fuel pump....
New-ish rad...kinda bent, but still works great.

I'll think of more later.
No tire kickers please.

GMC AMI · 10-31-2004, 06:45 PM

Sounds like a real decent deal for someone, good luck on your sale!

*rage'nrat638* · 10-31-2004, 06:45 PM

so what gengine do's it have's

72gord · 10-31-2004, 08:15 PM

What kind of shape is the box in? Rusty? Dents? I have 3 running motors but only one truck with good sheet metal!

Longhorn Man · 10-31-2004, 08:42 PM

The bed is all there, I'll asume lots of filler, and dented in on both quarter panels. The floor is almost perfectly solid, but very wavey.
Straight tailgate, but it too just looks better than what it really is.

Longhorn Man · 10-31-2004, 11:37 PM

rage'nrat638...it has a knocking 305 in front, and at the moment, a milkshake making 350 in the back. But I plan on getting the 350 out of there along with all the other crush weight back there.

blazerholic · 11-01-2004, 12:25 PM

Pics? Possible trades??

Blue Beard · 11-01-2004, 12:27 PM

I can't believe you of all people know you need to post pics....

Longhorn Man · 11-01-2004, 05:52 PM

pics...I can do that. Give me a few min to go out and shoot some decent ones.
Trades...not likely. You can try to tempt me, but I need cash more than anything else right now.

Longhorn Man · 11-01-2004, 06:35 PM

OK, here's a few...need to get more. Most came out like crap, had the digi-cam on the wrong setting.
First pic...69 chevy grill & fenders. (Actually fenders are 71/72) Messed up GMC Bumper. ignore the black brackets on the bumper and the wires...tow bar towing stuff.
Pic #2 This is the only rust holes in the bed. Like I said, minimal. There are a few drilled too, but nothing over 1/4 inch.
#3 inside cab roof rust.
#4 rear coils....VERY nice trailing arms. Probably the best you'll find in this part of the country...I think there is maybe a one inch spot where there is rust between the 2 halves...been a while since I looked...when I replaced the U-bolts...but none the less....very nice arms. While hose shocks look terible, they work great. (new ones up front)
#5 the straight bumper that I kinda don't want to sell...but it is bolted there right now and I have no place to store it. It is an original '70 bumper, not repro. Minimal damage and wear...as an original used part, I would gove it an 8 or so out of 10. You can also see the guard rail damage from the blow out I had 6 or so weeks ago. (on the lincoln)

I'll see if it isn't too dark for more pics.

Longhorn Man · 11-01-2004, 07:37 PM

Here's a bunch more
#1 It has mis matched rims..these are the front (notice the tread....dam near new tires up front) rims off a 70's jeep cherokee or something.
#2 engine from drivers side. Note the new heater hoses, many clamps, you can see the new plugs sticking out of the boots, the new-ish rad, the 2 year old (I think) Interstate battery...
#3 Passenger side...clutch fan, wide belt drive off 87 burb on alt...
#4 Edelbrock 750 manual choke performer series carb. HEI with new cap and roter.... .1/2 mile on both.

#5 Closer shot of belt set up...brand new t-stat housing...o-ring type, Mr Gasket brand. Edelbrock performer intake just cleaned, hand made alluminum block off plates for choke and EGR.

Longhorn Man · 11-01-2004, 07:50 PM

#1 AUX tranny cooler...off 88 ford ranger. Cleaned out 100% before used on this tranny
#2 Rear wheels....old turbines. Matching ones come up from time to time on e-bay...6 lug, 15 X 9.5 ...275/60 tires on the back...this is the drivers side...it still has tread, it is about 3 yrs old.
#3 Note the tilt, newer 4 spoke wheel, carpeting (kinda crappy) in dash aftermarket acc guages (all work but the AMP, not hooked up) Nice 6 month old seat cover, over blue stock '70 seat. Seat is in decent shape, a spring or two need work and a cover...out of a 70 CST...so it is a non flip and full foam unit. Chevrolet rubber floor mats, couple soft spots on the floor, but no holes in floor that I am aware of. (You can see some light where kick panels meet the floor though) The bare foot pedal comes off...I'm keeping that. Working heat, working am/fm cassette pull out stereo

with no speakers...you can hardly hear the radio anyways.

Lots of crap in there that will be pulled out. (stuff on the floor and seat...not talkin parts)
#4 Factory installed, never removed VIN plate. Matching title in my name ready to be sighned over.
#5 Better pic of the seat cover. '70 CST door panels, were blue, dyed black, look almost decent.

Longhorn Man · 11-01-2004, 07:54 PM

#1 Straight tailgate.
#2 Crappy bottom of tailgate. Some sheet metal rust too that you couldn't see on the outside panel.
#3 poor quality pic due to low lighting
#4 Same thing.
#5 mr Horse power rocks. But the small hole in the door blows. There is another one at the back of the drivers door. (door removed from Blue CST...lower trim holes still there for wood trim)

Longhorn Man · 11-01-2004, 08:21 PM

(Out dated pic) it cruises at a good RPM on the freeway...

Even at this speed...

(I had it to the 'm' In MPH on the bottom of the speedo...but no pic.

)
LED tail lights...

And brake lights...

Factory High hump cab floor.

Most of you know....this is the Blue CST I refered to. My first Longhorn.

I'll see if I can find more after I eat.

Longhorn Man · 11-01-2004, 08:51 PM

More pics...mostly different angles

Up high...

from the right rear

Don't worry about the decision on cutting the dash or not cutting it...

The one piece drive shaft (4 foot 10 inches) and the proper style short shaft TH350. I had it removed to install the 1900 RPM converter.

Longhorn Man · 11-02-2004, 07:39 PM

Bump

beagler · 11-02-2004, 10:06 PM

Quick question? Have you painted the truck red or black because some of the pics are red and some are black? Just curious. Also are you considering any trades?

*Randy70C-10* · 11-02-2004, 10:13 PM

You're selling the turd

You've had that one for a while dude.
beagle- It's black now, used to be red with a GMC clip.

Longhorn Man · 11-02-2004, 10:35 PM

It was red, with the correct GMC front end, and now black primer with a 69 Chevy front end.
I'm not planning on accepting any trades, but you can try anyways. You may convince me to do so.

Randy, going on 4 years with it...time to let it go, gotta get the Longhorn out of *her* driveway and on the road.

weasel29gm · 11-02-2004, 10:55 PM

I'll vouch for Andy on this. It would make a good beater or work truck!!! Good Luck!!

Longhorn Man · 11-04-2004, 06:10 AM

no one is interested?

big blue 72 · 11-04-2004, 11:20 AM

Andy, you know I have more $$ than common sense.
What's the least you will take for it?

8t5Silverado · 11-04-2004, 09:40 PM

I want it.

Would you consider a trade for a new aluminum Marin mountain bike with Shimano LX and XT parts with disc brakes?

Longhorn Man · 11-04-2004, 10:55 PM

Quote:

Originally Posted by big blue 72

Andy, you know I have more $$ than common sense.
What's the least you will take for it?

Man...I'm pretty much at my bottom dollar now. I may have a little wiggling room, but at this moment, I have to stick with the $650 price.

Quote:

Originally Posted by 8t5Silverado

I want it.

Would you consider a trade for a new aluminum Marin mountain bike with Shimano LX and XT parts with disc brakes?

Sounds like a decent bike...I've been out of the hobby for about 12 years or so when my Canondale got ripped off. But I have no place to store a nice bike nor honstly, the urge to ride one any more. I have too many back problems as it is.

Let me know...both of you. Sleep on it, PM me...or respond on here... I'll be off work at a decent time on saturday, and have sunday off. So if either of you are still interested...we can talk this weekend.

11-01-2004, 12:25 PM	#8
blazerholic I am a Gov't Mule Join Date: Aug 2003 Location: Latonia,Ky Posts: 276	Pics? Possible trades?? __________________ ...to die in the saddle must be my destiny, to ride this rockin' horse I must be crazy...

11-01-2004, 12:27 PM	#9
Blue Beard Registered User Join Date: Jan 2003 Location: Washington State Posts: 8,831	I can't believe you of all people know you need to post pics.... __________________ 1970 Chev CST 2003 Harley Fatboy 1975 Chevrolet Step Van 1956 Chev Bel Air 1977 Blazer 2WD For Sale $3000.00 1978 Blazer 2WD For Sale $7000.00 1978 Silverado 2005 Monte Carlo

11-01-2004, 06:35 PM	#11
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	OK, here's a few...need to get more. Most came out like crap, had the digi-cam on the wrong setting. First pic...69 chevy grill & fenders. (Actually fenders are 71/72) Messed up GMC Bumper. ignore the black brackets on the bumper and the wires...tow bar towing stuff. Pic #2 This is the only rust holes in the bed. Like I said, minimal. There are a few drilled too, but nothing over 1/4 inch. #3 inside cab roof rust. #4 rear coils....VERY nice trailing arms. Probably the best you'll find in this part of the country...I think there is maybe a one inch spot where there is rust between the 2 halves...been a while since I looked...when I replaced the U-bolts...but none the less....very nice arms. While hose shocks look terible, they work great. (new ones up front) #5 the straight bumper that I kinda don't want to sell...but it is bolted there right now and I have no place to store it. It is an original '70 bumper, not repro. Minimal damage and wear...as an original used part, I would gove it an 8 or so out of 10. You can also see the guard rail damage from the blow out I had 6 or so weeks ago. (on the lincoln) I'll see if it isn't too dark for more pics. Attached Images Last edited by Longhorn Man; 11-01-2004 at 08:08 PM.

11-01-2004, 07:37 PM	#12
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Here's a bunch more #1 It has mis matched rims..these are the front (notice the tread....dam near new tires up front) rims off a 70's jeep cherokee or something. #2 engine from drivers side. Note the new heater hoses, many clamps, you can see the new plugs sticking out of the boots, the new-ish rad, the 2 year old (I think) Interstate battery... #3 Passenger side...clutch fan, wide belt drive off 87 burb on alt... #4 Edelbrock 750 manual choke performer series carb. HEI with new cap and roter.... .1/2 mile on both. #5 Closer shot of belt set up...brand new t-stat housing...o-ring type, Mr Gasket brand. Edelbrock performer intake just cleaned, hand made alluminum block off plates for choke and EGR. Attached Images

11-01-2004, 07:50 PM	#13
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	#1 AUX tranny cooler...off 88 ford ranger. Cleaned out 100% before used on this tranny #2 Rear wheels....old turbines. Matching ones come up from time to time on e-bay...6 lug, 15 X 9.5 ...275/60 tires on the back...this is the drivers side...it still has tread, it is about 3 yrs old. #3 Note the tilt, newer 4 spoke wheel, carpeting (kinda crappy) in dash aftermarket acc guages (all work but the AMP, not hooked up) Nice 6 month old seat cover, over blue stock '70 seat. Seat is in decent shape, a spring or two need work and a cover...out of a 70 CST...so it is a non flip and full foam unit. Chevrolet rubber floor mats, couple soft spots on the floor, but no holes in floor that I am aware of. (You can see some light where kick panels meet the floor though) The bare foot pedal comes off...I'm keeping that. Working heat, working am/fm cassette pull out stereo with no speakers...you can hardly hear the radio anyways. Lots of crap in there that will be pulled out. (stuff on the floor and seat...not talkin parts) #4 Factory installed, never removed VIN plate. Matching title in my name ready to be sighned over. #5 Better pic of the seat cover. '70 CST door panels, were blue, dyed black, look almost decent. Attached Images

10-31-2004, 06:27 PM	#1
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	69 SWB GMC for sale Selling my short/fleet GMC (chevy front clip) It does run, but knocks like crazy once warmed up. The TH350 bolted up to it was rebuilt in 97 and has maybe 30K on it sence then. Never slipped once, fluid been chainged every year...is leaking a little though. B&M 1900 RPM converter. once piece drive shaft. Hooker comp headers. coil spring rearw/3.07 gears. Van tilt installed w/later 4 spoke GM wheel. edelbrock performer intake edelbrock 750/manual choke carb manual drum brakes in need of help big block engine towers. (dunno why, onless they were also V-6 towers) Buy it, slap a motor in it, do some brake work and have a fun daily driver/beater. If you want a truck to restore, this one needs lots of work. Most body panels almost look good at first sight, and look worse up close. Come and get it in columbus ohio, need a trailer or tow bar. Even though I can fire it up and move it, the headers are open and I'm selling it as not driveable. I might be able to deliver a short distance...100 miles or less. $650 as it sits, add 100 bucks and you can have the tow bar, tail light harness and safety chain. I'll get pics soon hopefully. Please answer w/questions, comments, pic requests...ect, on this thread, not in my PM box or e-mail. You'll get a quicker responce here anyways. Payable w/cash,money order,postal money order...can store here for a short period of time, not very long though. It is dead and parked on the street. Last edited by Longhorn Man; 10-31-2004 at 06:54 PM.

10-31-2004, 06:29 PM	#2
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Oh yea....home done LED tail lights and a very pretty engine with some cheap (but nice) chrome...if any of that is important. power steering Int reg alt HEI new-ish starter and fuel pump.... New-ish rad...kinda bent, but still works great. I'll think of more later. No tire kickers please. Last edited by Longhorn Man; 11-01-2004 at 12:30 AM.

10-31-2004, 06:45 PM	#3
GMC AMI Registered User Join Date: Apr 2004 Location: The Other Maine! Posts: 2,236	Good luck. Sounds like a real decent deal for someone, good luck on your sale!

10-31-2004, 06:45 PM	#4
rage'nrat638 Account Suspended Join Date: Mar 2003 Location: THE FALL GUY CHICAGO IL Posts: 5,883	so what gengine do's it have's

10-31-2004, 08:15 PM	#5
72gord Never enough time!! Join Date: Mar 2004 Location: sw Wisconsin Posts: 601	What kind of shape is the box in? Rusty? Dents? I have 3 running motors but only one truck with good sheet metal!

10-31-2004, 08:42 PM	#6
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	The bed is all there, I'll asume lots of filler, and dented in on both quarter panels. The floor is almost perfectly solid, but very wavey. Straight tailgate, but it too just looks better than what it really is.

10-31-2004, 11:37 PM	#7
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	rage'nrat638...it has a knocking 305 in front, and at the moment, a milkshake making 350 in the back. But I plan on getting the 350 out of there along with all the other crush weight back there.

11-01-2004, 05:52 PM	#10
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	pics...I can do that. Give me a few min to go out and shoot some decent ones. Trades...not likely. You can try to tempt me, but I need cash more than anything else right now.

11-01-2004, 07:54 PM	#14
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	#1 Straight tailgate. #2 Crappy bottom of tailgate. Some sheet metal rust too that you couldn't see on the outside panel. #3 poor quality pic due to low lighting #4 Same thing. #5 mr Horse power rocks. But the small hole in the door blows. There is another one at the back of the drivers door. (door removed from Blue CST...lower trim holes still there for wood trim) Attached Images

11-01-2004, 08:21 PM	#15
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	(Out dated pic) it cruises at a good RPM on the freeway... Even at this speed... (I had it to the 'm' In MPH on the bottom of the speedo...but no pic. ) LED tail lights... And brake lights... Factory High hump cab floor. Most of you know....this is the Blue CST I refered to. My first Longhorn. I'll see if I can find more after I eat.



Register or Log In To remove these advertisements.

11-01-2004, 08:51 PM	#16
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	More pics...mostly different angles Up high... from the right rear Don't worry about the decision on cutting the dash or not cutting it... The one piece drive shaft (4 foot 10 inches) and the proper style short shaft TH350. I had it removed to install the 1900 RPM converter.

11-02-2004, 07:39 PM	#17
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Bump

11-02-2004, 10:06 PM	#18
beagler Registered User Join Date: Oct 2004 Location: Cincy, OH Posts: 190	Quick question? Have you painted the truck red or black because some of the pics are red and some are black? Just curious. Also are you considering any trades?

11-02-2004, 10:13 PM	#19
Randy70C-10 Account Suspended Join Date: Mar 2001 Location: Virginia Beach, Va. U.S.A. Posts: 15,320	You're selling the turd You've had that one for a while dude. beagle- It's black now, used to be red with a GMC clip.

11-02-2004, 10:35 PM	#20
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	It was red, with the correct GMC front end, and now black primer with a 69 Chevy front end. I'm not planning on accepting any trades, but you can try anyways. You may convince me to do so. Randy, going on 4 years with it...time to let it go, gotta get the Longhorn out of her driveway and on the road.

11-02-2004, 10:55 PM	#21
weasel29gm SLOW BUT SURE,BUT CLOSER Join Date: Feb 2002 Location: eleanor wv usa Posts: 3,098	I'll vouch for Andy on this. It would make a good beater or work truck!!! Good Luck!! __________________ 69 C-10, OWNED 38YRS... 350 over 30, 350 Turbo, 3:73 Posi P/S, P/B Black with red and black int. ''LOVE THESE OLD ''TRUCKS.......

11-04-2004, 06:10 AM	#22
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	no one is interested?

11-04-2004, 11:20 AM	#23
big blue 72 Senior Member Join Date: May 2002 Location: hamilton,ohio,usa Posts: 1,499	Andy, you know I have more $$ than common sense. What's the least you will take for it?

11-04-2004, 09:40 PM	#24
8t5Silverado Mudslides 'r my specialty Join Date: Dec 2003 Location: STL Posts: 1,106	I want it. Would you consider a trade for a new aluminum Marin mountain bike with Shimano LX and XT parts with disc brakes? __________________ Always on the lookout for old cars and parts...(20s, 30s, 40s, 50s, 60s, etc.) http://www.cardomain.com/memberpage/500339 Last edited by 8t5Silverado; 11-04-2004 at 09:44 PM.

Register or Log In To remove these advertisements.