The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-28-2004, 09:53 PM   #1
skokie
Registered User
 
skokie's Avatar
 
Join Date: Oct 2003
Location: San Jose Ca.
Posts: 3,354
Brake Drum making scraping noise

I adjusted the brakes today and after I was done I noticed that the pass side is making a scraping noise. I am not sure if it was there before I started. Did I adjust to far?

Thanks
__________________
RIP to my son Dylan. 5/17/2002 - 8/18/2018
If you want to know more about rare forms of pediatric cancer or if you want to help fund pediatric cancer research, please check out the website for the non-profit I started.
https://slothforpedcancer.org



68 build thread
http://67-72chevytrucks.com/vboard/s...d.php?t=223234
skokie is offline   Reply With Quote
Old 11-28-2004, 10:44 PM   #2
Sweet72
Registered User
 
Sweet72's Avatar
 
Join Date: Nov 2003
Location: Alexandria, VA
Posts: 1,534
If the drums are true and not warped you probably adjusted them too far. I always make adjustments so the shoes are close but not scraping and then drive in reverse and apply the brakes and the self adjusters do the final adjusting
__________________
'72 GMC SWB C1500 Custom, frame-off in progress. 383 SBC, 9:1CR, Comp Cams XE262H, Scat internal balanced crank, Eagle SIR 6" rods, Keith Black dish pistons, Dart Iron Eagle 72/180 heads, Weiand Stealth intake, Stewart stage I water pump, Holley 4bbl vac sec, TH350 with B&M Shift Improver Kit. 12 bolt positraction.
Sweet72 is offline   Reply With Quote
Old 11-29-2004, 12:33 AM   #3
skokie
Registered User
 
skokie's Avatar
 
Join Date: Oct 2003
Location: San Jose Ca.
Posts: 3,354
After listening to them pass side a nit I think it it is warped. I am going to get new shoes and it turned tomorrow.
__________________
RIP to my son Dylan. 5/17/2002 - 8/18/2018
If you want to know more about rare forms of pediatric cancer or if you want to help fund pediatric cancer research, please check out the website for the non-profit I started.
https://slothforpedcancer.org



68 build thread
http://67-72chevytrucks.com/vboard/s...d.php?t=223234
skokie is offline   Reply With Quote
Old 11-29-2004, 02:51 AM   #4
skokie
Registered User
 
skokie's Avatar
 
Join Date: Oct 2003
Location: San Jose Ca.
Posts: 3,354
I drove it around some tonight and the pass side is warped.
__________________
RIP to my son Dylan. 5/17/2002 - 8/18/2018
If you want to know more about rare forms of pediatric cancer or if you want to help fund pediatric cancer research, please check out the website for the non-profit I started.
https://slothforpedcancer.org



68 build thread
http://67-72chevytrucks.com/vboard/s...d.php?t=223234
skokie is offline   Reply With Quote
Old 11-29-2004, 01:37 PM   #5
sneakysnake
It's a catastrophic success.
 
sneakysnake's Avatar
 
Join Date: Jan 2003
Location: Oklahoma
Posts: 2,077
Did you pull the drum and inspect before you adjusted?Nothing like adjusting out a worn out shoe.
sneakysnake is offline   Reply With Quote
Old 11-29-2004, 09:52 PM   #6
GlennBrittain
Senior Member
 
Join Date: Jun 2003
Location: Panola County Texas
Posts: 401
Brake Noise

Since you have not replaced your brakes, my reply is not your problem. However if you do replace the shoes, pay attention to the springs and the rod that goes thru the spring. Some one help mw with the proper name for the spring and rod. If you buy a brake spring kit from local auto parts store, it will most likely come with sprongs and rods for 1/2 ton and 3/4 ton brakes. If you install the 3/4 ton rods on 1/2 ton brake shoes, the ends of the rods will rub the drums. This noise is hard to find untill you have been there and done it.
GlennBrittain is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:40 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com