![]() |
|
![]() |
#1 |
Forever Grateful
Join Date: Mar 2001
Location: Forney,Texas
Posts: 779
|
painless wiring.....
so how painless is it..........has anyone ever done one of these to their vehicles??? if so is it pretty self explanatory.....reason for is that I have got wires everywhere and some are cut and some are not and it really bothers me.....I would like to prevent any fires if possible.... :roll: :roll: I have a 67 swb
__________________
R.I.P Dad 04-07-42 - 05-27-09 |
![]() |
![]() |
![]() |
#2 |
Lovin' Life in Miss.!
Join Date: Mar 2004
Location: Puckett, Mississippi
Posts: 1,937
|
I put in one. It was pretty easy. I had a little problem wiring it up so the front side markers would blink with the turn signals. It is prewired for non a/c trucks. If you have a/c you have to re-use your old a/c harness. It does come with new headlight, light switch, wiper, ign and heater connectors. You have to re-use almost everything else. I bought new side marker light conectors and re-used the tail lamps. I liked it ok. There was one problem. The bulkhead connector template in the instructions does not match up exactly with the connector. There was some extra cutting, trimming and fitting that had to take place. I think the board list some better manufacturers though. Just run a "painless" search. It will come up.
In hindsight, I probably really did not need a new harness. My main reason for wanting one was the old bulkhead connector looked like it had been arcing. I kept my old harness for referance and pet projects. After really looking at it the bulkhead connector was just covered in some kind black goop. The fuse connectors were tight in the block and nothing was melted. The onlything I really need to replace was the temp sending wire and I needed to get rid of the resistor wire. I could have taken my old harness out went over it and put it back in good as new. If you have the time for a complete re-wire you have time to remove and inspect your harness before ordering your new one. It might save you some money.
__________________
The truck... you hear that? No really, you did hear that?!!! |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Oct 2004
Location: DFW TX
Posts: 769
|
I have most of my painless harness installed at it was easy. The intructions are clear and everything goes where you think it would. I still have a few of the smaller connections to make but all in all i'd say for the price i have been pleased with the harness.
|
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Feb 2004
Location: BAY AREA!!
Posts: 44
|
my friend did his 70 GMC. he said it was easy. i'm going to do mine when i have a little more $$$$$
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jun 2004
Location: Reading PA
Posts: 164
|
so is it as easy as calling painless and telling them you have a 67 gmc with a 350 motor and they send it to you or is there other information you need to tell them???
__________________
98% of ALL fords are still on the road today... ![]() ![]() where is the best place to park a ford???.. next to a fire station!!!! ![]() pictures of my new and old trucks! |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Apr 2000
Location: Frisco, Tx, USA
Posts: 606
|
Red,
I went through this question phase last year and decided that the wires weren't so bad, or at least not enough were so bad, that they couldn't be replaced as needed versus the cost. Some of mine were down right hazardous, mainly the charging circuit. I went to Napa and got several rolls of automotive wire and spent a couple of days working it over. So far, it's been great. In the process, I added fusible links, relays, and junction blocks to bring it all a little more modern. The real reason I should have gone with a new harness would be to get a fuse block that doesn't have rusted terminals. That causes me more problems than any other electrical items. Rust is a fair insulator on fuse clips. What part of Dallas are you in?
__________________
http://home.comcast.net/~r.landrum/w...tos.html-.html '68 C-10 LWB, '98 Z-71 350 w/accessories (Serpentine), Edelbrock Performer, Edelbrock 1405 (600cfm) carb, GM HEI, CompCam Extreme 4x4 roller cam, Thorley Headers, Carter Electric Fuel Pump, Vintage Air, 700r4, 3.73, disc brakes and power steering upgrades. |
![]() |
![]() |
![]() |
#7 |
Forever Grateful
Join Date: Mar 2001
Location: Forney,Texas
Posts: 779
|
I'm in the mesquite area......
__________________
R.I.P Dad 04-07-42 - 05-27-09 |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Oct 2004
Location: DFW TX
Posts: 769
|
I got my painless harness from O'reileys but they also sell them at Autozone.
|
![]() |
![]() |
![]() |
#9 | |
Registered User
Join Date: Sep 2004
Location: Newark, DE
Posts: 81
|
Quote:
__________________
-Chops- |
|
![]() |
![]() |
![]() |
#10 |
Lovin' Life in Miss.!
Join Date: Mar 2004
Location: Puckett, Mississippi
Posts: 1,937
|
If you are kinda handy with electrics, you could go recreational junkyarding and get a used cab and engine harness. Go through it then as your time permits.
__________________
The truck... you hear that? No really, you did hear that?!!! |
![]() |
![]() |
![]() |
#11 |
Senior Member
Join Date: Mar 2000
Location: East Peoria, IL
Posts: 600
|
i'll be finishing a painless harness install on the 68 this weekend. there's not a better harness out there, especially if you've added/planning to add extra stuff. it's been very adaptable to the upgrades i've made. if the truck is more stock-type M&H and some others might be the better choice.
__________________
1968 C10 - 383, non-stop project 1969 Camaro - 327, bone stock family heirloom...soon to be LS/T56, Ridetech, all the goodies |
![]() |
![]() |
![]() |
#12 |
Weekend Warrior
Join Date: Oct 2004
Location: CT
Posts: 1,787
|
if you just get the "engine harness" - does it just plug into the firewall and the rest plugs into where it has to go or do you have to cut and splice everything? - cause if you have to do that it isn't worth it
__________________
-'07 GMC Sierra K2500HD -'66 C10 Suburban -'68/'71 K20 Service Bed Project -'69 Chevy C30 Mason Dump -'33Ford P/U 396ChevyPowered ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#13 |
Account Suspended
Join Date: Mar 2001
Location: Virginia Beach, Va. U.S.A.
Posts: 15,320
|
I've installed three of these kits so far, one in my Model A, one in the stepside and one in a buddy's truck. I'd do it again. Once installed (if you take your time) this kit is very clean and the under-dash wiring all plugs in the same as the original. The engine wiring and all lights come with crimp connectors.
|
![]() |
![]() |
![]() |
#14 |
Forever Grateful
Join Date: Mar 2001
Location: Forney,Texas
Posts: 779
|
is the diagram-instructions pretty self explanatory....this will be my first go around with electrical stuff........
__________________
R.I.P Dad 04-07-42 - 05-27-09 |
![]() |
![]() |
![]() |
#15 | |
Lovin' Life in Miss.!
Join Date: Mar 2004
Location: Puckett, Mississippi
Posts: 1,937
|
Quote:
Yes it just plugs in. There is a single bolt in the middle. After you remove the bolt you have to do a little prying. There is a gaket between the two and it is a little stiff to remove. It has been together 30 years. You can experiment removing it at the wrecking yard. I still have my old one. I could shoot you a pic of the bulkhead connector disconnected if you like.
__________________
The truck... you hear that? No really, you did hear that?!!! |
|
![]() |
![]() |
![]() |
#16 |
Senior Member
![]() Join Date: Sep 2002
Location: Greenfield Mass.
Posts: 551
|
![]()
can we call painless. I was under the impression we had to go through a dealer. ( autozone- napa ) does somebody have a number for them. this would be great,
![]() ![]() ![]() ![]()
__________________
Certifiably crazy person |
![]() |
![]() |
![]() |
#17 |
Senior Member
![]() Join Date: Mar 2001
Location: Cedar Park, TX
Posts: 686
|
I have used painless stuff for my truck, as well as for installing fuel injection in trucks that never had it.....the wire they supply is TXL, it is an extremely high quality wire, plus, its both color coded and labeled. It should be rather easy for the novice to install. You may have to use some of your old connector housings though. I have been more than pleased with painless products. If you get into a bind, they do have tech support (which I have used before) and can be quite helpful.
__________________
71 Chevy C-10 SWB Fleetside RamJet-350/4L60e & Compushift/3.73Posi See it at www.prismnet.com/~grzanich |
![]() |
![]() |
![]() |
Bookmarks |
|
|