clutch problem? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

whitesswj · 01-25-2005, 01:26 AM

What is the proper length of the V8 clutch z-bar??

I have both of the bars, one from a I6 and the other from a V8.

Which is the propper one, the longer or shorter one??

thanks, sswj

**'68OrangeSunshine** · 01-25-2005, 05:49 AM

I think the V8 Z-bar is shorter than the L6 type because the base of the V8 block is wider. Don't remember if the levers are longer, I was refering to the tube dimension. I have a spare L6 Z-bar I could measure tomorrow.

Tx Firefighter · 01-25-2005, 07:24 AM

I also have one of each if you need me to compare them and measure.

whitesswj · 01-25-2005, 08:59 AM

i need the measurement of the V8 tube. which one do i use on a V8?

whitesswj · 01-25-2005, 07:04 PM

ttt

crazy longhorn · 01-25-2005, 07:31 PM

6 5/8".... (so my longhorn says). crazyL

whitesswj · 01-25-2005, 08:04 PM

thanks, i think it's the shorter one of the two.

thanks, keep the comment's rolling. i need this confirmed. sswj

whitesswj · 01-25-2005, 10:48 PM

it's the longer one. I got it to hook up fine.

sswj

01-25-2005, 01:26 AM	#1
whitesswj Embrace the Redneck Join Date: Jan 2004 Location: Cabot, AR Posts: 1,334	clutch problem? What is the proper length of the V8 clutch z-bar?? I have both of the bars, one from a I6 and the other from a V8. Which is the propper one, the longer or shorter one?? thanks, sswj __________________ '01 Camaro *Son, you just can't get there from here...*

01-25-2005, 05:49 AM	#2
'68OrangeSunshine Senior Member Join Date: Feb 2002 Location: Tucson, AZ USA Posts: 7,439	I think the V8 Z-bar is shorter than the L6 type because the base of the V8 block is wider. Don't remember if the levers are longer, I was refering to the tube dimension. I have a spare L6 Z-bar I could measure tomorrow. __________________ Every 25 years I like to rebuild that 292, whether it needs it or not.

01-25-2005, 07:24 AM	#3
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	I also have one of each if you need me to compare them and measure. __________________ I'm on the Instagram- @Gearhead_Kevin

01-25-2005, 08:59 AM	#4
whitesswj Embrace the Redneck Join Date: Jan 2004 Location: Cabot, AR Posts: 1,334	i need the measurement of the V8 tube. which one do i use on a V8? __________________ '01 Camaro *Son, you just can't get there from here...*

01-25-2005, 07:04 PM	#5
whitesswj Embrace the Redneck Join Date: Jan 2004 Location: Cabot, AR Posts: 1,334	ttt __________________ '01 Camaro *Son, you just can't get there from here...*

01-25-2005, 07:31 PM	#6
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,402	6 5/8".... (so my longhorn says). crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

01-25-2005, 08:04 PM	#7
whitesswj Embrace the Redneck Join Date: Jan 2004 Location: Cabot, AR Posts: 1,334	thanks, i think it's the shorter one of the two. thanks, keep the comment's rolling. i need this confirmed. sswj __________________ '01 Camaro *Son, you just can't get there from here...*

01-25-2005, 10:48 PM	#8
whitesswj Embrace the Redneck Join Date: Jan 2004 Location: Cabot, AR Posts: 1,334	it's the longer one. I got it to hook up fine. sswj __________________ '01 Camaro *Son, you just can't get there from here...*



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.