help with tie rod and drag link - The 1947 - Present Chevrolet & GMC Truck Message Board Network

mapco · 02-26-2005, 05:32 PM

Any one got a good site or place to get parts for my 73 3/4 chevy 4x4. I have got the tie rod ends from the steering box to pit man arm. I need to replace the one that goes across the axle to the passanger side. Any help would be nice. Thanks

nu2-72 · 02-27-2005, 09:40 AM

Most of the vendors that advertise here can get them, auto parts stores have them and LMC in KansasCity, Mo. has a 73 up catalog for mail order as well.
Is this something that is hard to get in AK?

mapco · 03-01-2005, 12:12 AM

not hard just not the best for accuracy on the parts. It seems most the time I can find my parts online an get the #'s then just give them, about the easyest. Was just looking for the center drag link to make sure I got the right one. I replaced it already with a napa part but the shock mount whole was in a different place (taward the center not driver side). I changed it all out for dual stableizers so that was avoided. Thanks

**JIMs70GMC** · 03-01-2005, 06:57 PM

www.partsmike.com

02-26-2005, 05:32 PM	#1
mapco Registered User Join Date: Feb 2005 Location: Anchorage, AK Posts: 10	help with tie rod and drag link Any one got a good site or place to get parts for my 73 3/4 chevy 4x4. I have got the tie rod ends from the steering box to pit man arm. I need to replace the one that goes across the axle to the passanger side. Any help would be nice. Thanks

02-27-2005, 09:40 AM	#2
nu2-72 Senior Member Join Date: Apr 2001 Location: Amazonia, Mo. USA Posts: 2,821	Most of the vendors that advertise here can get them, auto parts stores have them and LMC in KansasCity, Mo. has a 73 up catalog for mail order as well. Is this something that is hard to get in AK? __________________ 72 3/4 4x4 350 4spd 72 3/4 4x4 350 auto 2004 Duramax Silverado 4x4 2006 Duramax Crew cab 4x4 2010 Harley Ultra Limited 2011 Harley Street Glide

03-01-2005, 06:57 PM	#4
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	www.partsmike.com __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

03-01-2005, 12:12 AM	#3
mapco Registered User Join Date: Feb 2005 Location: Anchorage, AK Posts: 10	not hard just not the best for accuracy on the parts. It seems most the time I can find my parts online an get the #'s then just give them, about the easyest. Was just looking for the center drag link to make sure I got the right one. I replaced it already with a napa part but the shock mount whole was in a different place (taward the center not driver side). I changed it all out for dual stableizers so that was avoided. Thanks



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.