|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
08-08-2005, 09:23 AM
|
#1 |
|
Registered User
Join Date: Mar 2005
Location: Melissa, TX
Posts: 799
|
Can you test the oil gauge?
My oil gauge is pegging on the high end. At idle, it is right in the middle. Is there a way to check it? I don't want to put after market gauges in the truck. If it's bad, I want to replace it.
__________________
68 short bed driver (71 clip on it now, swapping to 68 when weather cooperates) 67 short step project (will get SWB from the 68) 67 Camaro, #'s matching (my wife's) 03 Dodge Ram 2500 4x4 diesel 5 speed 4.10 rear |
|
|
|
08-08-2005, 10:21 AM
|
#2 |
|
Registered User
Join Date: Jun 2002
Location: Knoxville Tenn.
Posts: 3,058
|
New engine? Sounds ok to me. Full right is 60 PSI-30 in middle. Old engine (402) went a little past center-new engine (502) goes full right. I have another gauge and it reads 60 PSI when old gauge is full right.
__________________
56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer |
|
|
|
|
08-08-2005, 10:50 AM
|
#3 |
|
Registered User
Join Date: Mar 2005
Location: Melissa, TX
Posts: 799
|
Engine has 8-11000 miles on rebuild. Has Hi-perf oil pump. Just trying to make sure everything is working.
Thanks
__________________
68 short bed driver (71 clip on it now, swapping to 68 when weather cooperates) 67 short step project (will get SWB from the 68) 67 Camaro, #'s matching (my wife's) 03 Dodge Ram 2500 4x4 diesel 5 speed 4.10 rear |
|
|
|
|
08-08-2005, 11:35 AM
|
#4 | |||
|
Union Electrician
Join Date: Feb 2005
Location: Louisville, Ky.
Posts: 3,356
|
you need an 80 lb oil preesure gauge, and that would solve the pegging problem
__________________
 69 Custom-10 SWB FLEETSIDE  350/350 TH Dropped 3.5/5.5"Help support the board->HERE Board vendors -> Vendors list Zip:40272 Big Sandy Survivor... Quote:
Quote:
Quote:
|
|||
|
|
|
|
08-08-2005, 11:40 AM
|
#5 |
|
Registered User
Join Date: Mar 2005
Location: Melissa, TX
Posts: 799
|
As long as it's stock looking...
I want the inside of the truck to be either all stock, or all Autometer.... Stock is much cheaper...
__________________
68 short bed driver (71 clip on it now, swapping to 68 when weather cooperates) 67 short step project (will get SWB from the 68) 67 Camaro, #'s matching (my wife's) 03 Dodge Ram 2500 4x4 diesel 5 speed 4.10 rear |
|
|
|
|
08-08-2005, 12:06 PM
|
#6 |
|
Keepin an eye out
Join Date: Feb 2003
Location: So.Cal
Posts: 3,921
|
Mine pegs also as probably most out there, I would only worry if it goes to zero while its still running
__________________
1970 Chevy C10 SWB 5.3 1996 Toyota Tacoma SR5 4x4 2007 Vespa GTS 250 Scooter ZIP 91351 |
|
|
|
|
08-08-2005, 12:10 PM
|
#7 |
|
Registered User
Join Date: Mar 2005
Location: Melissa, TX
Posts: 799
|
 No doubt...I have 3 Autometer Phantom gauges, oil, temp and volt...but would need speedo and tach to complete the set and they are NOT cheap... I have speedwarning dash in my 71 that I may sell and set myself up with autometers.
__________________
68 short bed driver (71 clip on it now, swapping to 68 when weather cooperates) 67 short step project (will get SWB from the 68) 67 Camaro, #'s matching (my wife's) 03 Dodge Ram 2500 4x4 diesel 5 speed 4.10 rear |
|
|
|
|
08-08-2005, 10:13 PM
|
#8 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
You can get an 80psi guage from a c/40 and up truck, looks exactly like the one in your rig right now.
however, I see no point in all reality. If it pegs the guage, then you have plentyu of pressure. It's when it goes the other way that you need to worry. |
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
