making a P/S box dimple.... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

qksilver · 10-21-2005, 08:48 PM

I was going thru the suspension posts last night, about 154 of them trying to find something. I found what i was looking for my 58 panel. I came across a post saying that "Wes" had a quide on his web sight to dimple a frame so a P/S box would fit. I , for 2 reason, one is money the other is I want to make it look factory.
I tried Wes's , from Washington< web site but it wasn't on it. Does anybody have a link etx to show how to do this?
Thanks,
Steve

dwcsr · 10-22-2005, 04:32 AM

I did this on mine and it requires a dimple from a 73 -87 frame. I don't know how Wes did his but I just got the angle of the box on the 75 frame I had and cut it out and welded it into the 58 frame at the same angle. the bottom bolt will need to have a sleeve welded across the frame. you will want to box that area. I also drilled thru the boxed area and slid steel tubes in the bolt holes and welded the ends so it had a solid bolting area and would not collapse the frame when tightened.

qksilver · 10-22-2005, 05:36 AM

Thanks

Chevy4Life · 10-24-2005, 11:04 AM

Here is a link to Wes's panel with the dimpled frame. http://www.classicheartbeat.com/panel_5.htm
I did this to my 67'. All it took was a little heat and a ball peen hammer. Test fitting till the box sat flush to the frame. Only took a couple minutes to do. I'll see if I have a good picture of mine to post.

Chevy4Life · 10-24-2005, 11:20 AM

Here is the best shot I have of mine. It really doesn't take much. I don't think I went as far as Wes did, just enough that the box was flush with a little clearance between it and the frame.

qksilver · 10-24-2005, 12:25 PM

I apreciate it, I reread my post and saw I wasn't clear. I have 2 different trucks I was working on, the 58 and a 67. It was for the 67 I wanted to dimple the frame, so this works out.
For the 58 I saw a kit to mount a toyota 4X4 p/s box in the stock location. I have the box and am fabing up the mount for it now.
I can figure out almost anything but have learned to short cut the mistakes by asking questions.
Thanks again, this really helps
Steve

dwcsr · 10-24-2005, 11:09 AM

The frame on a 58 is different. It doesn't slope down like the one in the link. You may be able to ball peen it in but its just as easy to cut out a dimple and weld it into the 58 frame. That way you have the holes predrilled.

10-21-2005, 08:48 PM	#1
qksilver Senior Member Join Date: Dec 2004 Location: Southern Pines NC Posts: 3,853	making a P/S box dimple.... I was going thru the suspension posts last night, about 154 of them trying to find something. I found what i was looking for my 58 panel. I came across a post saying that "Wes" had a quide on his web sight to dimple a frame so a P/S box would fit. I , for 2 reason, one is money the other is I want to make it look factory. I tried Wes's , from Washington< web site but it wasn't on it. Does anybody have a link etx to show how to do this? Thanks, Steve

10-22-2005, 04:32 AM	#2
dwcsr Hollister Road Co. Join Date: Apr 2005 Location: Houston Posts: 6,131	Re: making a P/S box dimple.... I did this on mine and it requires a dimple from a 73 -87 frame. I don't know how Wes did his but I just got the angle of the box on the 75 frame I had and cut it out and welded it into the 58 frame at the same angle. the bottom bolt will need to have a sleeve welded across the frame. you will want to box that area. I also drilled thru the boxed area and slid steel tubes in the bolt holes and welded the ends so it had a solid bolting area and would not collapse the frame when tightened.

10-22-2005, 05:36 AM	#3
qksilver Senior Member Join Date: Dec 2004 Location: Southern Pines NC Posts: 3,853	Re: making a P/S box dimple.... Thanks

10-24-2005, 11:04 AM	#4
Chevy4Life Senior Member Join Date: Feb 2003 Location: Las Vegas, NV Posts: 749	Re: making a P/S box dimple.... Here is a link to Wes's panel with the dimpled frame. http://www.classicheartbeat.com/panel_5.htm I did this to my 67'. All it took was a little heat and a ball peen hammer. Test fitting till the box sat flush to the frame. Only took a couple minutes to do. I'll see if I have a good picture of mine to post.

10-24-2005, 11:20 AM	#5
Chevy4Life Senior Member Join Date: Feb 2003 Location: Las Vegas, NV Posts: 749	Re: making a P/S box dimple.... Here is the best shot I have of mine. It really doesn't take much. I don't think I went as far as Wes did, just enough that the box was flush with a little clearance between it and the frame. Attached Images

10-24-2005, 12:25 PM	#6
qksilver Senior Member Join Date: Dec 2004 Location: Southern Pines NC Posts: 3,853	Re: making a P/S box dimple.... I apreciate it, I reread my post and saw I wasn't clear. I have 2 different trucks I was working on, the 58 and a 67. It was for the 67 I wanted to dimple the frame, so this works out. For the 58 I saw a kit to mount a toyota 4X4 p/s box in the stock location. I have the box and am fabing up the mount for it now. I can figure out almost anything but have learned to short cut the mistakes by asking questions. Thanks again, this really helps Steve

10-24-2005, 11:09 AM	#7
dwcsr Hollister Road Co. Join Date: Apr 2005 Location: Houston Posts: 6,131	Re: making a P/S box dimple.... The frame on a 58 is different. It doesn't slope down like the one in the link. You may be able to ball peen it in but its just as easy to cut out a dimple and weld it into the 58 frame. That way you have the holes predrilled.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.