Scored some parts, have questions... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**too much stuff** · 12-10-2005, 06:56 PM

First question, are these correct 71 big block motor mount stands?
Second, the bracket on the throttle cable with the gm #, is that anything unusual? Or any bracket for a 71?
Third, what is the upper bracket on the accelerator? I know the lower is a th400 kickdown, but don't recall seeing the upper part before. Nothing was connected to it either.
Last, anything else i should look for on the truck before it gets squished? It is a 71 custom/30 deluxe. 133" dually. Thanks, Eric

Swbman · 12-10-2005, 07:07 PM

Looks like all the stuff you have is from a 1971 bbc 396 or 402 truck, the towers look to be bbc kinda hard to tell from the picture angle, the accelerator cable bracket is definitely from a bbc my bbc suburban and bbc 68 chevelle ss both have them, I know from a fact the acelerator pedal bracket is from a bbc truck backed up by a turbo 400 tranny in fact for some strange I have found them also on factory bbc installed trucks.

Bob Moore · 12-10-2005, 08:19 PM

If it is a 71 1ton dually, the front hubs should have adaptors on them to fit the dually style wheel and also be disc brake as well. Those parts are somewhat hard to find.

The carb bracket looks like a quad-jet item both BBC and SBC.

The in cab accel bracket is also BBC and SBC with T400 switch attached. The ear that sticks out is where the Hand Throttle cable attaches when so optioned.

I don't know if they started the larger diameter sway bar before 73 or not. You might look at the size.

da-burb · 12-10-2005, 09:36 PM

71-72 rear brake drums are a 2 year only item. Doubtfull if they are any good, but you never know.

Rod · 12-10-2005, 09:56 PM

Yah the engine brackets look 68-71 BB to me.

Might as well go grab the heat shield off the cab for the BB exhaust on pass side.

Rear drums are hard to find...I still try to find any that are any good within the tolerances.

Any fender emblems?

**too much stuff** · 12-10-2005, 11:17 PM

I did look at the swaybar and it looked like my 1/2 ton ones. How much work is it to get the rear drums off? I know what it takes on a 1/2 ton, but i don't play on the heavy duty much. It still has 4 dually wheels on it. I don't think the truck has a ton of miles, but it has been sitting for awhile. The fender emblem is custom/30
deluxe
It had 8-400 emblems on the fenders, and 396 listed in the glovebox. If any one close enough needs the running gear, i could buy the truck and hold it for abit. I think it will be reasonable. (i think a couple hundred would buy whats left)
And rod, i already got the heat shield, the tranny hi-hump with no holes and the power steering res.
Thanks for all the input.

teeitup · 12-11-2005, 12:48 AM

Was it cold when you took all these parts off????

Nice find Eric!!!

**too much stuff** · 12-11-2005, 01:21 PM

Randy, wasn't bad. We got to about 20 degrees, but the wind was brutal...

**truckdude239** · 12-11-2005, 01:58 PM

thje drums on an dully u have to remove the rear axles wheel bearings and everything else

**truckdude239** · 12-11-2005, 02:00 PM

if it to much trouble just grap the whole rearend

**too much stuff** · 12-12-2005, 01:13 AM

It would be easier to grab the whole truck if someone close enough could use it...

12-10-2005, 06:56 PM	#1
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,768	Scored some parts, have questions... First question, are these correct 71 big block motor mount stands? Second, the bracket on the throttle cable with the gm #, is that anything unusual? Or any bracket for a 71? Third, what is the upper bracket on the accelerator? I know the lower is a th400 kickdown, but don't recall seeing the upper part before. Nothing was connected to it either. Last, anything else i should look for on the truck before it gets squished? It is a 71 custom/30 deluxe. 133" dually. Thanks, Eric Attached Images __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

12-10-2005, 07:07 PM	#2
Swbman Senior Member Join Date: Mar 2004 Location: Tulsa,Oklahoma Posts: 606	Re: Scored some parts, have questions... Looks like all the stuff you have is from a 1971 bbc 396 or 402 truck, the towers look to be bbc kinda hard to tell from the picture angle, the accelerator cable bracket is definitely from a bbc my bbc suburban and bbc 68 chevelle ss both have them, I know from a fact the acelerator pedal bracket is from a bbc truck backed up by a turbo 400 tranny in fact for some strange I have found them also on factory bbc installed trucks. __________________ 1961 BUICK LESABRE 1968 CHEVELLE SS 396 1969 BUICK RIVIERA GS 1971 2 WHEEL DRIVE BLAZER 1971 4X4 BLAZER 1971 SHORTBED CHEYENNE FLEETSIDE 1971 SHORTBED 4X4 FLEETSIDE ** ...My Ebay

12-10-2005, 08:19 PM	#3
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: Scored some parts, have questions... If it is a 71 1ton dually, the front hubs should have adaptors on them to fit the dually style wheel and also be disc brake as well. Those parts are somewhat hard to find. The carb bracket looks like a quad-jet item both BBC and SBC. The in cab accel bracket is also BBC and SBC with T400 switch attached. The ear that sticks out is where the Hand Throttle cable attaches when so optioned. I don't know if they started the larger diameter sway bar before 73 or not. You might look at the size. __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow

12-10-2005, 09:36 PM	#4
da-burb "Ochre Ogre" Join Date: Apr 2000 Location: Springfield, MN Posts: 3,558	Re: Scored some parts, have questions... 71-72 rear brake drums are a 2 year only item. Doubtfull if they are any good, but you never know. __________________ Bowtie Truck Stop Inc. Mid-West GM Truck Restoration Parts Supplier Your Key Parts, Auto Metal Direct, Dynacorn, and Goodmark dealer. like us @ www.facebook.com/BowtieTruckStop 1971 C-10 Suburban (Ochre) 1971 K-10 Suburban (Ochre) 1972 C-10 Suburban (Ochre) 1972 K-20 Suburban (Yellow- that just aint right!) Springfield, Minnesota 56087

12-10-2005, 09:56 PM	#5
Rod Join Date: Dec 1999 Location: Eastern - Manitoba Canada, Winnipeg Posts: 4,369	Re: Scored some parts, have questions... Yah the engine brackets look 68-71 BB to me. Might as well go grab the heat shield off the cab for the BB exhaust on pass side. Rear drums are hard to find...I still try to find any that are any good within the tolerances. Any fender emblems?

12-10-2005, 11:17 PM	#6
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,768	Re: Scored some parts, have questions... I did look at the swaybar and it looked like my 1/2 ton ones. How much work is it to get the rear drums off? I know what it takes on a 1/2 ton, but i don't play on the heavy duty much. It still has 4 dually wheels on it. I don't think the truck has a ton of miles, but it has been sitting for awhile. The fender emblem is custom/30 deluxe It had 8-400 emblems on the fenders, and 396 listed in the glovebox. If any one close enough needs the running gear, i could buy the truck and hold it for abit. I think it will be reasonable. (i think a couple hundred would buy whats left) And rod, i already got the heat shield, the tranny hi-hump with no holes and the power steering res. Thanks for all the input. __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

12-11-2005, 12:48 AM	#7
teeitup Just like to part out trucks!! Join Date: Nov 2001 Location: Meriden, Ks-North of Topeka 10 miles Posts: 27,396	Re: Scored some parts, have questions... Was it cold when you took all these parts off???? Nice find Eric!!! __________________ 67 Chev swb stepside 4x4 283 4 speed SOLD 72 blazer 4x4 4 speed Cheyenne 72 GMC swb 4x4 fleet 4 speed, original paint 1958 Cameo (one of 1405 built, it was my dads) 2020 chevy Apex 4x4 crew cab 1969 Z28 with the 302 1980 chevy swb 4x4 1964 chevell Malibu SS 1976 K20, sold new originally out of my dads chevy dealership Members that I've met, over 200 probably closer to 300 in the 12 years I've been on this site, everyone I met "It was a pleasure"

12-11-2005, 01:21 PM	#8
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,768	Re: Scored some parts, have questions... Randy, wasn't bad. We got to about 20 degrees, but the wind was brutal... __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

12-11-2005, 01:58 PM	#9
truckdude239 Senior Member Join Date: Sep 2005 Location: Lewisville, Nc Posts: 10,237	Re: Scored some parts, have questions... thje drums on an dully u have to remove the rear axles wheel bearings and everything else __________________ David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube

12-11-2005, 02:00 PM	#10
truckdude239 Senior Member Join Date: Sep 2005 Location: Lewisville, Nc Posts: 10,237	Re: Scored some parts, have questions... if it to much trouble just grap the whole rearend __________________ David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube Last edited by truckdude239; 12-11-2005 at 02:00 PM.

12-12-2005, 01:13 AM	#11
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,768	Re: Scored some parts, have questions... It would be easier to grab the whole truck if someone close enough could use it... __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.