The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > All 4x4 Tech & Off Roading

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-15-2006, 07:51 PM   #1
JAKES 68GMC
Aluminum slot wheels rule...
 
Join Date: Jan 2006
Location: Maine
Posts: 6,211
67-72 4x4 t-case

Did most 67-72 Chevy/GMC trucks have divorced or married t-cases?

I have a married Rockwell 221 that has internal issues, and probably will need to convert to an NP 205 sometime, which doesn't seem to be any big deal according to past threads. Which is better, divorced or married? Is it any harder to swap from a married t-case to a divorced one?
Jake
JAKES 68GMC is offline   Reply With Quote
Old 02-15-2006, 10:50 PM   #2
special-K
Special Order

 
special-K's Avatar
 
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
Re: 67-72 4x4 t-case

More married t-cases.Doesn`t a divorced set-up need a trans and a t-case crossmember?The front d-shaft will be longer and the rear d-shaft will be shorter.You`ll need the t-case linkage for a divorced set-up.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed"

GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project)
GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling)
Tim

"Don't call me a redneck. I'm a rough cut country gentleman"

R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~
special-K is offline   Reply With Quote
Old 02-15-2006, 10:51 PM   #3
1969 GMC
Registered User
 
1969 GMC's Avatar
 
Join Date: Feb 2003
Location: The Rubber City
Posts: 5,498
Re: 67-72 4x4 t-case

If you are just going to replace your transfer case, the easiest swap would be to either another married Rockwell, or a married NP205. You'd need the adapter and sleeve out of the 205 donor vehicle, and then the x-member would have to go back a little bit. And the driveshafts would need attention then too.

If you went divorced, you'd have to get a 2wd tranny (or rebuild your current 465 with 2wd parts), a divorced transfer case, and then the jack shaft (that goes between tranny and transfer). I don't know if you could keep the stock x-member, perhaps if you found a divorced T221. Then you'd have to fabricate a linkage.
__________________
1969 GMC K2500
1996 Honda Accord
2007 Kawasaki KLR 650
1969 GMC is offline   Reply With Quote
Old 02-16-2006, 05:14 PM   #4
JAKES 68GMC
Aluminum slot wheels rule...
 
Join Date: Jan 2006
Location: Maine
Posts: 6,211
Re: 67-72 4x4 t-case

Ok thanks.
JAKES 68GMC is offline   Reply With Quote
Old 02-17-2006, 09:50 AM   #5
smokekiki
Mike
 
smokekiki's Avatar
 
Join Date: Jan 2003
Location: west chester pa
Posts: 2,473
Re: 67-72 4x4 t-case

The one tons had divorced transfer cases.They were conversions.
__________________
70'c/10, 71 suburban4x4 402bb, 72suburban 4/6 drop, 72k/5 4x4 blazer 4" lift 35 tires
smokekiki is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:17 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com