|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
07-21-2006, 02:52 PM
|
#1 |
|
Registered User
Join Date: Jul 2006
Location: Fresno, Ca
Posts: 154
|
Exhaust PICS PLEAZZZZZ!!!!!!!!
I want to see some setups on the exhaust.....I got a couple of guys to respond and special thanks to them. If at all possible I'd like to see more setups before I do the installation.....So again please post many pics of your exhaust.....how it's installed and especilly how it loooks....68 stepside is what im fixing up.....
|
|
|
|
07-21-2006, 04:28 PM
|
#2 |
|
Registered User
Join Date: Nov 2003
Location: st. louis area
Posts: 1,551
|
Re: Exhaust PICS PLEAZZZZZ!!!!!!!!
mine a 75 stepside... Ive got Sanderson shorty headers into 2.5" exhaust behind my mild 454. a pair of Dynomax Turbo mufflers & a pair od Corvette exhaust tips
__________________
75 GMC C-15 short/step factory 454, lowered |
|
|
|
|
07-22-2006, 09:35 PM
|
#3 |
|
-Praise the Lowered-
Join Date: Oct 2001
Location: Garland, Tx, USA
Posts: 280
|
Re: Exhaust PICS PLEAZZZZZ!!!!!!!!
CLICK HERE to see how I did my exhaust a couple years ago. The basic setup was a set of shorty headers, 2-1/2" pipe ran tightly against the frame rails, then up and over the trailing arms with dumps just prior to the rear end. Sounds really good. If you like that deep throaty sound. The muffs are Flowmaster 2-chambers (40 series).
__________________
Race-N-Jason ('71 Chevy C-10 LWB 454/TH350) ('07 Dodge Ram 2500, 5.9 Cummins/6-speed Manual) |
|
|
|
|
07-22-2006, 09:42 PM
|
#4 |
|
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,474
|
Re: Exhaust PICS PLEAZZZZZ!!!!!!!!
Mine is my linky, the 4wd, pages 13-16 I think
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
|
|
|
07-23-2006, 06:49 AM
|
#5 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: Exhaust PICS PLEAZZZZZ!!!!!!!!
How do most guys handle routing @ the trailing arm crossmember?I think I`ll cut-out holes in the c-member,weld pipe to reinforce,and slide`em through.Just would like to see routing there w/o going through the c-member.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
