Advice before I take the bed apart?

[msgross]

I am getting ready to remove my bed for the following reasons:

1. Clean up the back of the frame.
2. Add my new poly tank conversion
3. Add my NOS wood floor (old one was rotted)
4. Add new wheel wells
5. Add new E-brake cables and lines
6. Add my bumper with brackets (maybe a hitch if I find one)

Any thing else that I should do while it's off? Any advice, I plan to replae the cross sills as well during this so I might as well remove the bedside and front piece. The link below has pics of it...thanks in advance

http://picasaweb.google.com/hawkdriver2002

For those of you that have troubles with pictures or want something like "photobucket" that others use on here try this link... It's a new service that is free from google (I think that they are taking over the world!).

[Ricks1971]

I just took one apart. The bedside bolts are easier to take off if you tighten them and they snap off, rather than trying to loosen then as they spin. I found this after I took on side off the hard way.

[msgross]

how about the new bolts for the bedside to wheel well? Were they easy? snapping off bolts is what i'm good at!!

[qksilver]

That is definity the way. Snap them off and be done with it

[timcos]

Let's see some pics. I will be doing this same thing in the spring.

Tim

Originally Posted by msgross

I am getting ready to remove my bed for the following reasons:

1. Clean up the back of the frame.
2. Add my new poly tank conversion
3. Add my NOS wood floor (old one was rotted)
4. Add new wheel wells
5. Add new E-brake cables and lines
6. Add my bumper with brackets (maybe a hitch if I find one)

Any thing else that I should do while it's off? Any advice, I plan to replae the cross sills as well during this so I might as well remove the bedside and front piece. The link below has pics of it...thanks in advance

http://picasaweb.google.com/hawkdriver2002

For those of you that have troubles with pictures or want something like "photobucket" that others use on here try this link... It's a new service that is free from google (I think that they are taking over the world!).

[67ChevyRedneck]

What kind of poly tank? A blazer? With the tank empty it may be a good time to mock up what you want to do with a filler neck, etc before you take the bed off (also to make sure you don't have clearance issues) if it's a blazer tank you won't.... Here's what I did.

You can check my "build thread" in my sig for lots of pics of my tank install and I welded a 96 silverado fuel door in my stepside fender.

[mbgmike]

Originally Posted by 67ChevyRedneck

What kind of poly tank? A blazer? With the tank empty it may be a good time to mock up what you want to do with a filler neck, etc before you take the bed off (also to make sure you don't have clearance issues) if it's a blazer tank you won't.... Here's what I did.

You can check my "build thread" in my sig for lots of pics of my tank install and I welded a 96 silverado fuel door in my stepside fender.

I like the straps

[67ChevyRedneck]

Originally Posted by mbgmike

I like the straps

Yeah, I didn't have money for the real ones. These snapped after the first tank of gas. I had to use bailing wire and duct tape to get home. I've done some real stupid crap in my time

They were just easy to do the "mock up" with

[mbgmike]

Originally Posted by 67ChevyRedneck

Yeah, I didn't have money for the real ones. These snapped after the first tank of gas. I had to use bailing wire and duct tape to get home. I've done some real stupid crap in my time

They were just easy to do the "mock up" with

I used a rubber bungee cord to hold up an exhaust pipe once. I works great for a little while.

I need to put a gas tank in my 65 c10 stepside.You think that one would work in mine?

[Richard Dobson]

WD-40 everything, then try to loosen the nuts to see if the carriage bolt square shank will hold in the bedsides. If they turn some before seizing up you can get a pair of vice grips onto the head of the carriage bolt. If that don't work try grinding the heads off. I used a 4" grinder. There are (2)welds and the back of the rear sill and (1) on top of it also on each side if you are removing the bedsides. Good luck

[northerngmc]

Originally Posted by msgross

I am getting ready to remove my bed for the following reasons:

3. Add my NOS wood floor (old one was rotted)

Where did you find NOS wood? Did the dealers used to stock wood?

[Green Machine]

If the rear rubber brake like needs replaced, or if it never has been replaced, now would be a good time. They usually seize onto the steel line, in the frame, well actually the flare nut rusts to line making it impossible to turn. If that happens, cut the rubber line and unscrew it from the metal line and don't bother trying to get the flare to turn on the line, it will ruin your day. Anyway it is much easier to get to now.

[msgross]

thanks...I am planning on a total brake replacement. (lines,mc, add a booster, wheel cylinders etc...)

I got the entire bed off now, updated photos on my album.

www.picasaweb.google.com/hawkdriver2002

[bonson]

replace any bushings & their respective bolts you encounter. I am slowly and eventaully conveting to polyurethane.
I would also clean up and spray the frame with that stuff that looks like LineX/Rhino liner kind of stuff that you buy in can. I also sprayed that under the new wheel wells I installed. (i never relmoved the bed for this)